Quantcast
Jump to content


Recommended Posts

Posted

Hi All, again,

Now the Landmaster will not engage in Forward or Reverse, less than 20 hours run time.

Did a quick diagnostic with Navitas Dashboard App, problem:

Bus Under Voltage Fault

Description: Voltage on controller B+ has dropped below 18V
Check batteries, solenoid and connections
(3-1)

Email problem to Navitas.

Still 50% battery supply, charging anyway.

Will check items above plus wiring tomorrow, sun going down.

D. Newton

American Landmaster, EV, Purchase Aug 2022.

Extras - Power Steering, Roof, USB port.

Posted

I noticed you added some manuals for your American Landmaster EV, thank you for sharing. Hopefully you will figure out the issue. This is one of the few EV topics I have seen, but I'm sure it'll grow as EVs become more widespread.

Here are your manuals. I edited the screenshot and descriptions.

 

Posted
On 11/10/2022 at 6:55 PM, D. Newton said:

Hi All, again,

Now the Landmaster will not engage in Forward or Reverse, less than 20 hours run time.

Did a quick diagnostic with Navitas Dashboard App, problem:

Bus Under Voltage Fault

Description: Voltage on controller B+ has dropped below 18V
Check batteries, solenoid and connections
(3-1)

Email problem to Navitas.

Still 50% battery supply, charging anyway.

Will check items above plus wiring tomorrow, sun going down.

D. Newton

American Landmaster, EV, Purchase Aug 2022.

Extras - Power Steering, Roof, USB port.

Hi All, Well I did some troubleshooting (shotgun work), and I got the vehicle working.  I think the connect was not seated fully in the DC/DC Convertor (48v to 12V).  Not sure, I disconnected and reconnected a lot of wiring connectors.  See Pic1

I was using the phone App, Dashboard from Navatis to communicate with TAC2 EZ-GO RXV Controller, the green brick, it has Bluetooth.  The App is not very stable, I had to uninstall and reinstall to get it to work.  Just a reminder.  Don

Motor Control.jpg

DC to DC Converter 01 Loose Conn.jpg

TAC2 EZ GO RXV.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Jim Kessell
      Hello
      Looking  for source information for a Landmaster Bulldog BD 700 doors and/or enclosure.  Anyone out there with a source please let me know. 
      thanks 
      Jim
    • By BigWave
      I turned off the key and then tried to start it a minute later and it would not start. I changed out the fuel filter and the injector. still nothing. if i have the injector pulled out and close to the hole the injector will spray fuel into the hole and it will run but the minute you put the injector in it will die. any idea's please
       
       
      Bigwave
       
    • By Ed Michael
      My older LM 650 is blowing fuel into the air cleaner.  Any idea on what would cause this?  It is the Suzuki motor.  Not sure what model year it is.
      Thanks
      Subaru SxS.mp4
    • By Mike Jenkins
      I have a 2013 Hisun with a 686 Yamaha engine.
      I purchased it from an individual and it ran fine as long as the battery was full.
      I replaced the stator and now it will not start (run).  It cranks fine, has fuel pressure, but will not fire up.  I replaced the coil, no luck there.
      a technician told me that it was the wrong stator and wants a mint to replace it.
      the wires all plugged in when I installed the stator.
       
    • By Homeowner A
      I was randomly and briefly able to connect to my Coleman UTV 400s ECU the other day twice and haven't been able to since.  When I was able to access it, I found the following codes and wondered if anyone may know where I should start or what I should look at?  
      P0031 - O2 Sensor Heater Control Voltage Low
      P0107 - Manifold Absolute Pressure/Barometer Pressure Voltage Low
      P0113 - Intake Air Temperature Sensor Voltage High
      P0118 - Engine Coolant Temperature Sensor Voltage High
      P0650 - Malfunction Indicator Lamp (MIL) failure
       
×
×
  • Create New...