Quantcast
Jump to content


2017 Cub Cadet Challenger 750 hisun junk motor

hisun junk

By hisun junk
in Cub Cadet UTV SxS Forum

 Share

Recommended Posts

hisun junk Rookie

hisun junk

Posted
Posted

As I tried to do a conversion with the Yamaha 660 motor, I realized the 660 was never fuel injected so it would not work for the fuel injected hisun motor swap. But the good thing is the hisun 750 motor is a clone of the 660 Yamaha but with the components for the fuel injection (cam/crank position sensor). So that left me with a new rebuilt Yamaha 660 and still a broke 750 hisun motor. I took apart 750 think the timing chain had broke from all that I've heard about these motors. The chain was not broke, but just off cam and crank gears! The chain tensioner was at fault!  I've ordered Yamaha 660 replacement parts, chain, two exhaust valves (which got bent when chain came off while motor was spinning) and seals. The piston has 2 little nicks where it had hit valves but no damage otherwise. The head is being redone at the machine shop and I'll be putting it back together in the next couple of weeks. Also I finally tracked down a Service Manual with all the info on the 550/750 Challenger.

hisun750.JPG

  • Like 1
Lucas Lenartowicz Rookie

Lucas Lenartowicz

Posted
Posted

Keep us posted, wondering how the yamaha will fit. So far I've had good success with aftermarket yamaha parts but haven't tried internal parts so curious to see. The Hisun parts can be difficult to get sometimes, and not necessarily cheap. I haven't looked at comparing oem yamaha prices with oem hisun but i know that some aftermarket yamaha parts are cheaper.

  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • esmarkey
      2018 cub cadet 750 challenger clutch issues?
      By esmarkey
      Hi, I purchased a used Cub Cadet 750 Challenger that seemed like the belt was slipping so I put a new belt in.  It still acts like the belt is slipping but now I am thinking it is the clutch? 
      What is the best way to remedy this problem? 
      Can the clutch be rebuilt?
      Are there aftermarket clutches available? 
    • Burk
      2021 Axis(Hisun) 700 Will not fire up
      By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • HISUN Sector 750 EPS Failu
      Is Your HISUN Loud?
      By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...