Quantcast
Jump to content


Low beam on T-boss 550

Rufus Fruge

By Rufus Fruge
in UTV General Discussion

 Share

Recommended Posts

  • 2 weeks later...
TapBoss Collaborator

TapBoss

Posted
Posted

Not sure what you’re calling low beams. Are you referring to the bottom and middle switch positions?  Agree that that setting is useless. Would like it to be a 3 setting switch so there was an actual “off” setting. 

Rufus Fruge Rookie

Rufus Fruge

Posted
  • Author
Posted

Found out that there are no low beams on the tboss 550. You can purchase an insert from massimo that will fit in the blank spot and can be connected to existing wiring under the hood. I’m not going to worry about it since I bought two lights and have them mounted on the bull bar. Works fine.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Topics

    • AlphaSerenity
      Hisun Axis 500 Problems - Hesitation, struggles to go up incline, and low speed regardless of gear range
      By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • MilSurpYinzer
      New Mexico etc
      By MilSurpYinzer
      I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
      Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
    • Eman85
      New owner Massimo MSU500
      By Eman85
      I just purchased a Massimo MSU500 and no manual came with it so I have some questions. looking for part #'s and availability of basics like spark plug air and fuel filter. What is the valve adjustment specifications? 
        Is there a fuel drain? It's been sitting, low mileage but I want to drain out the old fuel and put fresh. 
    • MilSurpYinzer
      Altering running lights
      By MilSurpYinzer
      Anyone decent with electrical work that knows a good tutorial on how to make my running lights switch off all together but also turn back on when I need too? I'd assume that my lights are hard wired to the battery or the fuse panel.
      Vehicle is a Kawasaki Krx 1000
      I'm looking to ad IR driving lights for night vision and short of just putting black tape over the lights I feel this would be a more efficient option and it would be cooler. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...