Quantcast
Jump to content

Coleman UTV 400 Stuttering / Rough Idle

Rusty Beavers
 Share

Recommended Posts

Rusty Beavers Newbie

Rusty Beavers

Posted
Posted

I'm working on a Coleman UTV 400 that has a rough idle, owner has had it for about a year. When I say it has a rough idle, it doesn't have the continuous smooth running sound. At times you can hear it kinda skip, sputter, or like the RPM has fallen (RPM stay constant according to the gauge) It's not as bad as it was after I replaced the fuel filter and fuel injector (both are Chiki) not sure if that is a quality brand at this point. Checked the spark plug, it was a little foul, but not too bad. (Since the engine is still idling bad I'm going to replace that) Cleaned the throttle body making sure the carbon and soot has been removed, and the air-filter has been cleaned. New fuel is being used so it's not old or been standing. They did tell me that they were using non-ethanol fuel, not sure if that would be causing the issue. Next two things I can think of that maybe the issue is the O2 sensor or the valves need adjusting.

Thoughts and suggestions? Thanks in advance.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • buckrub
      trying to finish assembly "new" 2021 Coleman ut 400
      By buckrub
      Hey guys! Newbie here. I'm an old man who's better with plowing a mule (4-legged kind) than these newfangled beasts. I, and a friend of mine, just bought new Coleman sxs and are having to finish the assembly. I've been reading on this site and I'm falling on the mercy of you experts. The only way I'm an expert is that an "ex" is a has been, and a spurt is a drip under pressure. LOL First off, the 2 buggies have no ignition switches. They seem to mount on the dash, not the opening in the steering wheel shaft cover, so we ordered new ones that are supposed to fit. They are 8 inches long, and have a 4-wired white plugin which is slightly rectangled when looking at the end of the plug. The trouble is there's nothing to plug into. There is a three-wire grey plug close enough to reach the four-wire plug, but of course, they are not compatible. 
      Secondly, the blinker, light, ect. unit on steering wheel just spins around when touched. I see no way in heaven or earth to secure it. I've looked at a diagram on the Powersports site, but can't detect how it mounted. Fellows I'd be so grateful for any help with this. Me and my mule will even plow your garden for free, for your help. LOL 
       
    • ETHIEL
      2012 Coleman 500 UT plug keeps fouling.
      By ETHIEL
      Spark plug keeps fouling. after 10-15 minutes of running any ideas what to look fore 
    • AlaskaTrail
      2021 Coleman UT400 - Transmission fluid change
      By AlaskaTrail
      Hi All,
      New to UTVs and recently accuired a ut400 from our local Alaska Commercial Co. and had a questions regarding the transmission fluid. I have had a squeeling noise, sounds like a teapot, that recently started after being driven for a few minutes. The manual says to change the fluid at 500 miles, so I was thinking maybe its just time for this to be changed. Other then that I cannot find any information regarding the type used. While reading through these forums, I seen someone put that the transmission is lubricated with the engine oil. Is this true? If not what should I be using and where can I find the information to change it out? Any input on this would be greatly appretiated!
      Thanks in advance
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • moonrover
      Coleman 2022 UT 400 radiator thermo switch replacement question
      By moonrover
      Mine is overheated/burned/melt at connection with its wire connector, parts are ordered to replace both them.  This seems to be a common issue, and some of you already replaced it. I right now just connect the wires, so the fan runs  all the time whenever the initiation is on, but it's better let fan runs as needed with a working temperature sensor/switch. 
      Question: Does some coolant come out by removing the switch/sensor from radiator?  Or, is the threaded hole all the way inside radiator?   If the answer is yes,  I want to drain or extract  some coolant to make its level below the sensor before replacing it, so I don't make a mess with coolant spilled out 
      Thank you.  

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...