Quantcast
Jump to content


new lever 4x4 locker

plumber

By plumber
in Joyner UTV SxS Forum

 Share

Recommended Posts

brostar Proficient

brostar

Posted
Posted

Have not done one but I would imagine something like this:

1/ Locate the electric locker behind the front axle on the drivers side. It's a plastic box.

2 /Disconnect the plug-in wire and tape over old connecter (you might need it again) .

3/ Then unscrew the old locker(not screws on cover but protruding from the base) and pull it out towards the rear. Do not pull straight out towards you, a small rod engager needs to come out of the axel first and that needs to slide away from the axle to the back.

4 /Your new kit should have the same screw paten as the old locker. Install the new locker making sure it is properly in line with the entry point into the axle. Also make sure you drive the engager home into the axle and then tighten the fasteners.

5/ Now if you have a Trooper with the fuel tank in the front, you are on your own here and you will have to use your imagination a bit with regards to where the lever placement will be. If you have a newer Trooper the fuel tank wont be a problem, just install to the right of the front locker lever. Make sure the cable is clear of obstructions by using cable ties.

My suggestions with a fuel tank at the front are: Install low down & in level with the left of the hydraulic reservoirs, or replace lever with a manual chock set up and install anywhere, or just contact Lenny who has designed and fitted one himself. Once done, you will be all smiles. If the old electric locker has stopped working, it can be fixed if you haven't stripped the plastic gears.

I hope this helps and good luck.

Cheers Mike.

plumber Proficient

plumber

Posted
  • Author
Posted

Thanks brostar I think I have it figure out it comes with a whole new end that you have to put on your diff have to take out the drive shaft out to install it. It looks like a good set-up my electric locker was not bad I just thought it was a cheap way to do it so I wanted something better I'll put pic in my trooper folk folder Thanks again David

brostar Proficient

brostar

Posted
Posted

Talk about a stab in the dark. Does it use the same engager port, surely it must do? Regardless, you will have to take out the old locker. If the old port in not getting used, it will have to be plugged. I would of thought it would be a lot easier to base the new one around the old engager, making it a bolt off, bolt on. Never mind, at least you know it wont let you down.

Cheers Mike.

brostar Proficient

brostar

Posted
Posted

I understand now. Looks failsafe and solid. Will the lever go beside the front locker lever OK? You might be able to leave the old locker in and use it as a plug, just make sure the engager is out then disconnect the wire plug.

Cheers Mike.

plumber Proficient

plumber

Posted
  • Author
Posted

I understand now. Looks failsafe and solid. Will the lever go beside the front locker lever OK? You might be able to leave the old locker in and use it as a plug, just make sure the engager is out then disconnect the wire plug.

Cheers Mike.

Thats were they told me to put it I have not install it yet I'm real busy with work it will be two weeks before I can do it.The old locker and housing you don't use that housing is a completely new housing

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • GBarney
      d1105T install in rtv 1000?
      By GBarney
      Recently bought a 2010 RTV 1100 with bad engine. a d1105T out of a toro 5400 just came available locally. Looking for info on if anybody has installed the turbo version of this engine, what challenges/ problems were encountered, how it turned out.
       
      Looks like nobody has any insight. I will complete installation and report back as to how it went, how it works, and what's involved.
    • Wolfpaak
      Identify this part help needed
      By Wolfpaak
      I think this part is causing a high idle problem(4000 rpm at start up) in my 04 R4 Joyner. I took it out and cleaned it and the problem went away. I just went out to start my SXS and it's idle jumped up to 4 grand again. Can someone tell me what this part is called so I can search for a new one. Or can you point me towards a source. 
      Thanks in advance. 
      Kenny


    • Jon Spruill
      2018 Hisun Sector 1000 Crew stalling but starts right back up. Please help!
      By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • Marie
      2013 Hisun 800 Please Help Wiring
      By Marie
      Hello, we recently got a 2013 Hisun 800 as a little project for my husband and I to work on. Turns out the guys before us loved the mud anyway. We have replaced the stator and now going to do the Rectifier but here is the hold up as seen in the picture. There are tons of wires going to the battery. I cant seem to find anything that shows what wires should, or shouldn't be attached to the battery or where these 2 plugs go. if someone would please take some pics or share knowledge to where they go I would appreciate it greatly.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...