Quantcast
Jump to content


2013 UT 500 won't go into reverse.

lonerider98

By lonerider98
in Coleman UTV SxS Forum

 Share

Recommended Posts

lonerider98 Rookie

lonerider98

Posted
Posted

At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!

Ben1098 Enthusiast

Ben1098

Posted
Posted

Look up some of my old posts on shift issues.  The throw from the shifter end is "less than" the required travel to get F N and R.  Adjustment of the shift linkage will give

F and N....or.....N and R.  Look for the post on how to shorted by 1/8" by cuttiing the "bell crank" plate and rewelding  to make it shorter.  

Dale Stansbery Explorer

Dale Stansbery

Posted
Posted

I imagine my 550 linkage is similar to your 500. I have to be sure my engine is at complete idle, and sometimes have to press hard on my brake to get it to shift into reverse. Now it may be the adjustment is a little off, but so far the above steps has allowed me to get it into reverse.

  • 2 weeks later...
aefron88 Community Regular

aefron88

Posted
Posted

Try playing with the adjustment. The 500/550's don't have the same shifter cable/lever issues as the 40's but the cable can stretch over time.

If you're getting grinding and popping out of gear it could be worn clutch dogs too, which require some effort to replace as they're internal to the transmission.

If you're having shift issues and grinding it's best to be proactive about adjusting because it does damage the dogs over time, and eventually will just pop out of gear at will once the dogs are rounded enough.

  • Like 1
  • 3 weeks later...
lonerider98 Rookie

lonerider98

Posted
  • Author
Posted
On 3/22/2024 at 11:41 AM, lonerider98 said:

At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!

So when push hard on the brake and I mean hard it will go into reverse. Is there a brake switch that could be going bad or Do you all think it's a adjustment fro the shift cable?

I haven't had a lot of time to really get into this. just picking brains right now. Thanks for any help!!

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Dave Jones
      2021 Coleman ut400 rev limiter
      By Dave Jones
      So with seat belt on  I can only get up to 20mph then it starts bucking until I get under 20 again. Diconnected the seatbelt and same thing. Reconnected seatbelt and unplugged speed sensor. Zoom..it flies. But now I have no speedometer. I have a new speedometer sensor on the way..any other ideas?
    • Mitch13
      Coleman 400 wiring help
      By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • Hunterman22
      2021 Hisun 500 Axis. Reading Codes??
      By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...