Quantcast
Jump to content


Ramp assist for trailer

Quig

By Quig
in Joyner UTV SxS Forum

 Share

Recommended Posts

Quig Community Regular

Quig

Posted
Posted

I'm in need of ramp assist for my utv trailer. I found a few, just ckg to see if anyone here knows anything about which is good,or better.Or has found & used different one. I can't lift much or bend very well, sooo, I need something to help? Wife won't lift it either!!! : )

Quig

check these out

http://www.easternmarine.com/Double-Barrel-Trailer-Gate-Assist-RA27C--0/

http://www.easternmarine.com/BUYERS-EZ-Gate-Trailer-Tailgate-Lift-Assist-5201000/

Was told by very wise member, that he almost missed my post, I put it in general discussion, utv forum,, "sorry" :unsure::)

Quig Community Regular

Quig

Posted
  • Author
Posted

Thanks for pics,that could well be my next project. not sure yet, have to have shoulder,& neck surgery, might not be cranking anything.

Kinarfi Veteran

Kinarfi

Posted
Posted

Thanks for pics,that could well be my next project. not sure yet, have to have shoulder,& neck surgery, might not be cranking anything.

I was thinking, since you have to have tail lights on your trailer, maybe some method can be rigged so that you turn your tail lights on, then you have a switch that steals the power from the lights and runs a motor to run the winch up and down. It would be simple electrically, but finding a light weight power winch could be difficult. Any one out there know of such a thing?

Kinarfi

Quig Community Regular

Quig

Posted
  • Author
Posted

Just throwing a cheap option out there. Could you use your trooper winch?

Thats pretty smart thinking, But, I'm really leaning towards 120.00 spring loaded example, really simple.. Thanks though,,Quig

Guest Lenny

Guest Lenny

Posted
Posted

Thats pretty smart thinking, But, I'm really leaning towards 120.00 spring loaded example, really simple.. Thanks though,,Quig

I would think you could use the gas springs. They are cheap and available in most any length and force while small and simple to hook up.

Lenny

  • 2 weeks later...
Quig Community Regular

Quig

Posted
  • Author
Posted

Well, I went with the easy lift,,,http://www.easternmarine.com/BUYERS-EZ-Gate-Trailer-Tailgate-Lift-Assist-5201000/

Got it installed, works great!! No more groaning & moaning. Very easy to install. Even "Quig" did it!! :rolleyes: :rolleyes: :rolleyes: :rolleyes:

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • AaronD1982
      Massimo Buck 400S UTV Stator......?
      By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • Jamie 67
      Why is there 2 different length keys for my tboss 1000
      By Jamie 67
      Why is there 2 different length keys for my tboss 1000?
    • Mitch13
      Coleman 400 wiring help
      By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • AaronD1982
      Massimo 400S Buck UTV Starter solenoid replacement
      By AaronD1982
      I recently purchased a 2019 or 2020 (no manual) Massimo 400S Buck Series UTV.  It ran fine for a couple days but the low battery light was flashing while it drove.  It then died in the field one day and I was able to jump the battery and get it rolling enough to get back to the barn.  It started both times I turned the key for a couple days after and when driven died 10 minutes later in the driveway.  Even after jumping it had no juice, but with the key out of the ignition it kept trying to start, a quick look on the Google machine and it suggested starter solenoid or ignition switch was the culprit.  Fair enough, let's just order a replacement solenoid, right?  No way Jose....the pin connector on the UTV is a 2-pin white plastic connector and the part received is a 4 pin.  How do I swap that and make it work?  Can I even?  Where do I find correct parts in the future?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...