Quantcast
Jump to content


Recommended Posts

Posted

Well, I decided the Joyner T4 needed a few mods. This is a work in progress, but will be fantastic when I am finished. I am hoping to have it done no later than August 1st.

I am building a sub-frame for the T4, removing all axles, A-arms, diffs, etc from the Trooper. I will be installing a 4 link, with King Coil Over Shox (39in), Transfer Case, Jeep Dana 60 axles built with 4.88 gears, bump cage for the T-Case, and somewhere between 44" - 54" Boggers.

The rear of the Joyner is also getting a new look due to an engine swap and auto trans. I havent decided yet if I am going to put in the 6cyl out of the jeep I bought or a SB 302. This will be the last thing to be completed.

I have just started building the sub-frame and removed all of the drive-train.

I will have a lot of pics of the build, but may take me a little while to post.

WHY???

I havent driven the Joyner in a while as we always take the Brute Force's out to ride. Everywhere we go has nothing but lakes and mud pits, and with the length of the T4 I high center way to often. South East Texas is lacking the dunes that you all ride on. LOL!!!

Posted

Sounds Great! But (there is always a but) you will have a rock crawler, not a Trooper anymore. But (there goes another one) this is not a negative. Look forward to seeing what you do as there maybe a middle ground between a stocker & what you are doing that may interest me. Thanks for letting us know about your project and POST PICS.

rocmoc n AZ/Mexico

Posted

Nah, not building it for rock crawling, or I would have went with 14 bolt axles and housing. This will be specifically for the mud and lakes, and creeks. Will be outfitted with a fantastic sound system and a huge cooler for beer and shots!!

Posted

I like the sound of it. It kind of reminds me of a Commando four seater build No Limits did 3 or 4 years ago, but this time with teeth. If I went to a six, I would look a a Lexus or Toyota 2JZ-GE 3L. It’s light, powerfully and has many upgrades in it’s standard form. It’s the same engine the Supra RZ used so easy to add the stock twin turbocharges and in sequential configuration the output goes from 169kW( 227hp) up to 206kW (267hp) at 5600 rpm. That would be nice in mud holes. The tranny is a 5 speed auto with Tiptronic, the best of both worlds and the block looks like it would fit into the Troopers frame. It’s more square than long. If your will to fabricate a new rear, then a longer Jeep engine might be the way to go. Pushing the rear seats up is going to give you more room and the rear passengers better forward viewing, kind of like a RZR-4.

Your going you have many issues to troubleshoot and I know there will be plenty of people here following your progress and adding their thoughts.

I can wait to see this beast.

Cheers Mike.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
    • By MilSurpYinzer
      Hey all, I was just wondering what you guys consider a necessary upgrade or spare part to have or mod onto your machine.
      I'm going for a kind of shtf survival rig that's not going to be SUPER heavy and I'm looking at getting:
      A spare belt (I keep seeing this mentioned everywhere I look so it must be important)
      A spare tire and mount( So would I need a jack like one from an old jeep or something else?)
      Tire chains for the winter
      And maybe a cargo bed upgrade so things don't slide out.
      Bumpers because duh.
      I already installed high output lights and have a windshield, roof, back window, and winch. And I outfitted a Molle panel for the back of my passenger seat with extra supplies like food, first aid, and spare mags.
      Any advise on increasing durability, longevity, and having something on hand because it's absolutely necessary would be a plus.
      Thanks so much!
×
×
  • Create New...