-
Similar Topics
-
By ita47
I currently have a 2011 Polaris 400 H.O. that has fewer than 300 hrs on it. My buddy bought it new and I bought it with around 100 hrs. I use it around the farm and to get between two properties that are about a mile apart. I am tired of dealing with the choke when its cold or even cool out. It starts fine and runs ok if your driving but until it gets completely warmed up if you pull up to a gate and get off to open it will die. And because of the choke my wife has a hard time with it. Before I got the 400 I had a 2013 polaris 500 midsize that was fuel injected but aways ran rich and foul plugs. I had it at two different dealers and neither one could fix it. So I sold it and bought the 400. My father in law has a 2015 Polaris 570 midsize which is fuel injected and it is hard to start and cranks more than it should. Needless to say I am done with Polaris and ready to sell mine and move on to something better.
I have been looking at the Honda Pioneer 700 and the Kawasaki Mule Pro MX. I was disappointed to learn the Kawasaki Mule Pro MX engine is built by Hysun and not Kawasaki, but that maybe a non issue. Maybe I'm missing another good option that I haven't considered. The main thing is getting something that is bullet proof reliable. Any feedback would be greatly appreciated.
Thanks in advance
-
By Hig
Just purchased a new Axis 700 which was delivered a few days ago. It's May 2023 and I received a 2021 model. Do they upgrade their model years like a car? The Axis 700 was brand new but the model year stunned me.
-
By J R
Hi, I just bought a used 2015 MSU500 with 365 hrs on it. After riding it the UTV seemed sluggish and would not climb a moderate hill without getting a running start in low range. Took it to a repair shop and they told me that the clutches were burnt and slipping. Had the primary clutch replaced and afterwards was told that the compression of the cylinder was only 80psi, which I was told was 100psi below original compression. I've bought all parts necessary, including new crankshaft and bearings to rebuild the motor. My question is, does anyone know if a 700cc top end kit will bolt onto the 500 motor case?
-
By CYJSP2009
Hello Everyone
Brand new Joyner CV AXLES are waiting to be unloaded at LA port and then be sent to warehouses in Charleston, TN , BALTIMORE, MD and Groveport, OH. Estimate they will be available for shipments to end customers in about 2-3 weeks.
These CV AXLES are ordered in February this year and now it is middle July. Very long time to get these parts. Qty for each model is not big. Detail as below:
S/N Part No. Description Charleston, TN BALTIMORE, MD Groveport, OH Total
1 D650.03.02.02.00 650 Sand Spider Rear left 3 2 3 8
2 S650.03.02.02.00 650 Commando Rear 7 6 10 23
3 TR1100.03.01.03.00 TR1100 Front 3 3 4 10
4 D650.03.02.03.00 650 Sand Spider Rear Right 3 2 4 9
5 S800.03.02.02.00-R2 800 R2/4 Rear Shaft 4 4 6 14
6 TR1100.03.02.03.00 TR1100 Rear 6 5 9 20
7 S650.03.01.02.00 650 Commando Front Left 3 3 4 10
8 S650.03.01.03.00 650 Commando Front Right 3 3 4 10
Below items are also available. These items can be shipped in days
CAGE:
1. 800 Renegade R2/R4 Front outer cage --- 5 pieces
2. 800 Viper SV1100 Drive shaft rear Left outer cage --- 5 pieces
3. 800 Viper SV1100 Drive shaft rear left inner cage --- 3 pieces
CV BOOT:
1. 650 Commando Left Front / 650 Commando Right Front /650 Sand Spider Rear Left / 650 Sand Spider Rear right / OUT CAGE 2 pieces
2. 650 Commando Rear OUT CAGE 1 pieces
3 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE 2 pieces
4 650 Commando Left Front / 650 Commando Right Front INNER CAGE 1 pieces
5 650 Sand Spider Rear Left / 650 Sand Spider Rear right INNER CAGE 1 pieces
6 650 Commando Rear INNER CAGE 1 pieces
7 Trooper Front / Trooper Rear / 800 R2 R4 Rear OUT CAGE INNER CAGE 2 pieces
Anyone who need above items please contact me at [email protected]. Thanks.
Other Joyner items needed, you can also contact me and I will try to help.
Have good day
Casey / Leaf Asia
2021-07-20
-
By vern
Hi there,
My name is Vern and im in Alaska. I have a 2019 ranger 1000 xp HL crew. So the machine had zero issues with clutch or shifting. then the belt blew. i got the new Polaris belt installed with no issues. i cleaned everything and made sure all belt debris was removed. installed new belt. now it lurches in gear and is hard to shift if at all. when i insert clutch spacing tool in secondary and relieve belt pressure then in shifts when off no problem. the secondary is spinning fast when in park or neutral. i did try adding and removing shims from secondary also without any change. the primary moves in and out without issue. it appears there is no issue with primary or secondary. im stumped. can u help please.
-
-
-
Gallery Images
.jpg.eaae3d80b123b73a4bba230f0313e154.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.