Quantcast
Jump to content


TIE ROD ENDS

bill&mary

By bill&mary
in Joyner UTV SxS Forum

 Share

Recommended Posts

bill&mary Rookie

bill&mary

Posted
  • Author
Posted

Has anybody replaced tie rod ends? seems like there should be a part to replace with.factory part sucks.

Thanks,plumber. Do these have dust boot? Also why didn't you get theMHMR-16z,they have grease fitting?

plumber Proficient

plumber

Posted
Posted

Thanks,plumber. Do these have dust boot? Also why didn't you get theMHMR-16z,they have grease fitting?

I didn't see any dust boots I did get the mhmr-16z But the grease fitting is so small that they broke off just geasing them so I bought the mhmr-16t.

bill&mary Rookie

bill&mary

Posted
  • Author
Posted

Thanks,plumber. Do these have dust boot? Also why didn't you get theMHMR-16z,they have grease fitting?

also theses look different than mine.mine don't have through bolt. they look like the ones on ebay #270793660912.he says these will fit just don't want to replace with junk.thanks

plumber Proficient

plumber

Posted
Posted

also theses look different than mine.mine don't have through bolt. they look like the ones on ebay #270793660912.he says these will fit just don't want to replace with junk.thanks

I'm sorry they are rod ends you need tie rod ends the ones I showed you goes on the a-arms.On the tie rod I replace mine with stock one I don't know of any tie rod ends sorry about that

  • 2 months later...
lowgear Enthusiast

lowgear

Posted
Posted

also theses look different than mine.mine don't have through bolt. they look like the ones on ebay #270793660912.he says these will fit just don't want to replace with junk.thanks

The tie rod ends on e-bay 270793660912 will not work the are for smaller joyners, threads and shaft size are different. I e-mailed them and asked about threads I don't remember the size but they were wrong. I got mine from JMC motors. Call them to make sure you get tie rod ends not ball joints. I had a small problem, when I ordered them on line the ware house sent ball joints, talk to Casey he will get you the right part. there is a problem with descriptions. They call both ball joints. I would also recommend changing the zerk fittings. They treated me great, corrected my problem no hassel.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Wolfpaak
      Identify this part help needed
      By Wolfpaak
      I think this part is causing a high idle problem(4000 rpm at start up) in my 04 R4 Joyner. I took it out and cleaned it and the problem went away. I just went out to start my SXS and it's idle jumped up to 4 grand again. Can someone tell me what this part is called so I can search for a new one. Or can you point me towards a source. 
      Thanks in advance. 
      Kenny


    • Edelbrock
      What UTV should I buy?
      By Edelbrock
      So I'm interested in a side by side of some sort.
      Not sure what make/model to even look at.
       
      I would plan on riding on trails with very rough rocky terrain and plenty of mud. Maybe sand once in a long while. I like LOTS of power and drive fast, but also like a trail that is a challenge to get through. I think 4x4 would be a must. I like the idea of a supercharged engine, but I have never owned one, and would be a little concerned about long term reliability or expensive difficult engine repairs. If anyone knows quads, my favorite was the 2008 Polaris Outlaw 525 IRS. For dirt bikes, I raced a 2008 KTM 450 SX-F. So that gives you an idea of what type of off road stuff I liked.
      I don't like "utility quads" or "trail bikes". And likewise, I dont want a turd UTV. I want something that looks awesome and performs awesome. 2 seater with some cargo capacity at the minimum.
       
       
      Thoughts?
    • FTG-05
      Want a new work UTV; who and what should I look for?
      By FTG-05
      I want to ditch my Kubota RTV-XG850 and its moronic twitchy throttle design flaw, get rid of the problematic engine and the 40 mph purposely throttled speed.
      So far, I'm looking at the Honda Pioneer 1000 and the Polaris Ranger 1000, both of which have 1000-1500 lb payload bed capacity.
      What other makes and models should I be looking at?
       
      Thanks for the help!
    • Grant
      Can’t figure out what part I’m missing
      By Grant
      I recently bought an axis 500 and it’s missing a box or something the plug is L shaped I’ve looked through the wiring diagrams and still can’t figure it out. The plug is located right near the battery housing 

    • lincolnsq175
      Are there any performance parts for ut400?
      By lincolnsq175
      Ive searched and cannot find any performance parts that fit my machine.
      I have a 2020 coleman ut400.
      Im looking for machined sheave kit, programmers, cdi, exhaust and intake.
      I know these are yamaha rhino clones but are they rhino 450 clones?
       
      Any info is appreciated.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...