Quantcast
Jump to content


2009 Mule Trans R&R front shock

Txsmurph

By Txsmurph
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

Txsmurph Newbie

Txsmurph

Posted
Posted

I have a 2009 Mule Trans that I bought with a 4" lift. I believe that the rt front shock is broken. ? is there anything special that I need to be aware of while removing and replacing the shock? Where to support the suspension, tools...Thanks

rocmoc Grand Master

rocmoc

Posted
Posted

You will need to lift and support the frontend on jack stands. Then you can put a jack under the front suspension arm and lift to where you can move the shock around with it's own slack at the bolts. After you remove the nuts on the mounting bolts, you should be able to remove the bolts with you finger tips. If you can raise or lower the suspension arm until you have the slack. Use box wrenches so you don't round the bolt & nut edges. A bottle jack or floorjack and jack stands. You may have to remove the wheel to have enough room to work. Good luck!

rocmoc n AZ

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Cletus
      Nonexistent Customer Support?
      By Cletus
      Getting some work done on my sector 550 at a dealer, having issues with some parts. Dealer has tried, i have tryed, its been a month and hisun customer support has not emailed or called either one of us back.
      Meantime my sector is sitting torn apart in the shop collecting dust. Apparently hisun doesnt give a ratsazz about their customers, anyone else having the same problem getting ahold of them? Sick of this crap.
       
    • mrpro
      Coleman UT400 rear shock height adjustment
      By mrpro
      I got the fronts adjusted.  I'm trying to raise the ride height in the rear, but my spanner wrench keeps slipping.  Is there an easier better way?  It's like there's too much pressure working against me to be able to twist the height adjusters.  How can I relieve that tension to make them easier to turn?  
    • jertex
      Shift cable problem, 2017 Stampede 900, need advice
      By jertex
      I bought a 2017 Stampede 900 last fall that was new, old stock with less than 5 hours on it thinking that I would be getting a relatively trouble free UTV as compared to buying a used Polaris or CanAm, or Honda, etc. It's been a little quirky, but reliable. What I thought was just a minor issue with this model, the difficulty in shifting between R, N, L, H, etc., was just a characteristic of this model is now a big problem. I had to climb two very steep trails to get to the upper meadow of our hunting property, which seemed to stress the UTV more than usual since I was carrying some lumber to work on a platform for a hunting blind, and when I went to shift into park, I felt something give and it would not shift out of low, but it did move up into high gear.  I couldn't get it to shift at all at that point and the shifter felt mushy for lack of a better word. I was able to get it down to the lodge and when I investigated, I discovered that the straight, metal tube portion of the shift cable had bent to almost 90 degrees (see pics). I'm positive that it had already had some deformation that had happened previously and it had the right amount of resistance to bend to the point where it was unusable. 
      I have two questions:
      1. I suspect that there must be some other issues that makes this UTV difficult to shift, and I'm wondering if this is a common problem and if someone could enlighten me on what could cause this to be difficult to shift?
      2. Have any of you had this happen and if so, how difficult is it to replace the shifter cable?
      Any other advice is welcome, this is the first UTV that I've ever owned, so I don't know much about working on these or maintaining them. I'm relatively capable when it comes to working on my own vehicles in general, and I'm not afraid to take things apart and get my hands dirty.
      Thanks in advance for any insight, I'll be traveling most the day so I won't get a chance to look at replies until this evening.


       
    • Jeff freeman
      Utv wont start and broken fuel injection wire
      By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • AaronD1982
      Hoping someone out there somewhere can help.....2019 Massimo Buck 400S
      By AaronD1982
      Onto the next problem, everything has been replaced in the charging system except the Flywheel Rotor, I have it torn apart all the way down to said rotor, but it is suggested that a specific puller is required, and a compatible rotor seems virtually impossible to find.  I can find many like it, but this one is mine scenario for those that get the reference.  For all I know I have the last Massimo Buck 400S on the planet and will never find another part again, but who knows.  Any ideas, help or otherwise that anyone might have would be greatly appreciated.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...