Quantcast
Jump to content


Finishing the Small Items/Problems on Project Jeep

rocmoc

By rocmoc
in All Other Off-Road Toys

 Share

Recommended Posts

rocmoc Grand Master

rocmoc

Posted
Posted

One of the problems that kept us from taking the Jeep with us was my Jeep was leaning on the left side (lower on the driver's side) after everything was mounted; New tires, new wheels, new leaf springs, new shakles & new diffs. It also caused the Jeep to dive on the driver's side when you turned quickly towards the right. I couldn't find the cause and I was under a timeline, time was running out. I was too reactionary! While traveling and upon the return home, I told myself to slow down, think and measure. I have fixed stuff like this before. So today I took the time to measure and just lay under the Jeep looking at the frame. Inch by inch comparing left side to right side. THEN, I SAW IT! The frame supporting the front spring hanger on the rear diff on the driver's side was bent. I took a floor jack and lifted the frame at the location aprox the amount of the bend and sure enough the Jeep was nearly level. In one of my shops when I poured the floor I installed tie-downs in case I ever had a problem like this. I will tie her down, jack her up until the bend is gone. I will then box both sides so this can't happen in the future. Must have happened when the right rear axle came out on the previous owner. I never saw it as the axle was hanging out when I bought her. At any rate it is a good day when you solve a problem!

rocmoc n AZ/Mexico

  • 3 weeks later...
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

Turned out there was A LOT of small items / problems. One I have been working on is the Jeep rode and handled like cr*p. I did every easy fix there is but no improvement. Finally I took the leaf springs apart and removed 2 leafs leaving 4 in the stack. I also put a wedge in the front spring mount to improve caster. WOW what an improvement. The springs now have travel so the shocks can work. I am going to bite the bullet and purchase Fox Shocks. It seems except in the racing community, Jeep suspension technology is lagging behind. At any rate progess has been made. Second problem was / is exhaust noise. There was so much at first I could not tell the NEW Headman Headers had leaks. Finally after clearing up some of the noise I found the leaks. The surfaces of the flange is not flat & one pipe is not fully weld. I can't return them as I had to redesign one tube for clearance around the steering column. So, I have it off and doing the fixes myself. All in all I am feeling better about the new beast.

rocmoc n AZ/Mexico

  • 2 weeks later...
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

Have been working on the handling and made BIG improvements yesterday. Added a lot more caster! She is now ready for the road. Very few rattles & small stuff left. Will continue to work on those but it is time to buy the insurance so she can be driven. Will make little local trips to post office and the such then move on to bigger trips & off road. It is getting there.

rocmoc n AZ/Mexico

  • 2 weeks later...
rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

WELL, the handling turned out the be a BIG item/issue. A Jeep requires 4+ degrees of postitve caster to drive correctly. If you have less the steering will wander making it very difficult to stay on even a smooth road. A mod I had planned for the future is reversing the shackles in the front. The spring hangers are reversed where the shackle is in the rear and the pivot / solid mount end is moved to the front. This mod ends up with A LOT of postitive caster. It worked. Completed the mod and for the first time I can drive the Jeep at speed. One more of those little items/issues and I can start enjoying. Oh yeah, two more little items/issues. Turns out I have to rebuild the transfer case, $400.

rocmoc n AZ/Mexico

nocturnalsixer Rising Star

nocturnalsixer

Posted
Posted

Ouch $400...i remember when i had to rebuild my transfer case in my 02 silverado i end up doing it myself for $400 in parts and lube, I'm more than sure you would be able to tackle a older trasfer case i just hope it's not iron

Sent from my DROID RAZR using Tapatalk 2

rocmoc Grand Master

rocmoc

Posted
  • Author
Posted

Ouch $400...i remember when i had to rebuild my transfer case in my 02 silverado i end up doing it myself for $400 in parts and lube, I'm more than sure you would be able to tackle a older trasfer case i just hope it's not iron

Sent from my DROID RAZR using Tapatalk 2

Good news is I still have money in the budget from the sale of my Troopers. A couple of things I don't work on is Trannys, Transfer Cases & Diffs. I will do everything else. $400 isn't that bad. I got a quote for replacing the front & rear tranny seals and the rear diff seal on a '57 Ford I own. $600 so just adding fluids & drip-pan as everthing works well, just drips.

rocmoc n AZ/Mexico

  • 5 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Topics

    • AlphaSerenity
      Hisun Axis 500 Problems - Hesitation, struggles to go up incline, and low speed regardless of gear range
      By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • Cliffampranch
      2025 Amp Crew Ranch Edition range issues and questions.
      By Cliffampranch
      Hi All,
      I have a 14 mile round trip on level roads to reach the property where I work with my 2025 Amp Crew Ranch (purchased, April 2026).  That 14 mile round trip uses 60% of the battery as shown on the gage for a calculated range of 23.3 miles versus an advertised “up to 50 miles” range.  A mile or two working on the property gets me a flashing gage and warning beeping by the time I get home.  The dealer was good to work with and even with a new battery (yesterday) the results were about the same, although there seemed to be more power and a higher top speed.  I own a Mach-e Mustang so I am familiar with how various conditions affect range, but less than 50% of advertised range just seems like there has to be something out of whack.
      Now I’m wondering if there is a controller and/or software issue affecting the range and performance.  At various points the Amp seems to lose power for no reason and then has trouble maintaining speed.  Any ideas?
      Also, twice now, the brakes seem to have not released fully.  After noticing reduced speed, I stopped and check the rotors and wheel…..HOT!  So, now every time I feel less power, I stopped to cycle the brakes and check the temperature.  Very annoying.  Are there any adjustments to be had?
      And yes, as noted in another post, sometimes the switching from forward to reverse or high to low speed feels sluggish or balky.
      Lastly, while an electric vehicle powertrain is quiet, my Amp was horrible from a road noise and vibration standpoint.  This was easily fixed by locating panels vibrating on other panels or the frame (even the cup holders were vibrating) and installing felt adhesive pads at the contact points (seat to frame, windshield to frame, fenders to frame, etc.).  This is a $10 and 1/2 hour fix that makes a significant improvement in the driver/passenger experience.  Tire noise, yes, but that’s because of the knobby tread.
      I’m trying hard to like my Amp and would appreciate any tips, advice or solutions.
    • Firewalker918
      Anyone customized their uv34XL? Also, looking for seatcovers
      By Firewalker918
      I have a 2021 UV34XL and I am kind of looking to change it up from the orange wheels and maybe do a wrap?  Please share photos of any XLs that has been modified to look better and any seat covers recommended.thanks
       
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...