Quantcast
Jump to content


Help, just bought a T2 and trying to get it running right

Nickb1907

By Nickb1907
in Joyner UTV SxS Forum

 Share

Recommended Posts

Nickb1907 Rookie

Nickb1907

Posted
Posted

I found this forum trying to find any info I could on these things. I never heard of a Joyner, but I got a hell of deal on buying a 2010 T2 Trooper. It has a lot of problems and I am trying to work through everything. If you have a writeup or could even grab a part number off yours it would be extremely helpful. I have a rats nest of wiring to figure out.

1. Engine Idle-Starting it cold it will not idle. I have to hed down the gas for about 1-2 minutes and slowing bring it down to get an idle.

2. Dies when you push in the clutch when running high rpms-If i keep shifts slow and below 3K it will keep going, but if I run it up and then try and put the clutch in it will die.

3. Relays and fuses- I have spots where there should be relays and fuses and there is nothing. I need a part number for all the relays and the location that they should be plugged in. The manual doesnt call out anythign on the relay sizes. I think I can get all the fuse sizes from the manual. I should have this figured out tomorrow.

4. Fan control-The fan and headlights were wired into the turn signal switch. How does the utv handle the fan? Is it controlled by the computer to turn on at a certain temp?

5. Temp sensor doesnt work-This might be why the fan was wired into a switch. Need info on how to fix.

6. Fuel gauge doesnt work-Anything on this would be helpful.

7. Front and rear locker adjustment-If I could get pictures on the rear that would be helpful. The front looks right, but doesnt lock. The rear is missing the bracket that the front locker had going into the diff that located the cable and probably allowed adjustment.

8. Clutch-The sweet spot is at the very end of the pedal, almost where you would remove your foot from it. The sweet spot is also very small. Is your clutch like this or is there some adjustment that needs to be made. It also doesnt feel firm enough. Any input here would help.

9. Brakes-They dont work great. It stops the utv but it isnt very fast.

10. Lights- I would like to know what each switch should control and what plugs they go to. All I have is the roof rack lights working. The other switches do nothing and there are no more lights to turn on.

I appreciate any advice and help you can give. This thing is a blast but I really would like to get it up and reliable before I start doing serious trail riding.

Thanks

Guest Lenny

Guest Lenny

Posted
Posted

Thats a lot of stuff and a lot of your answers are already posted on this forum. I sujest your go tothe top of the forum pinned post and read everything from there down for about, well way back on topics. Like the diff locker adjustments are clearly detailed out. This happens to be in the pinned topics part. We will fill in the gaps for you but some of this stuff takes a lot of writing to detail out and it is already done for you. We will be glad to help but go thru the already explained stuff first. There is a lot of good solutions already posted.

Welcome to the forum.

Lenny

Nickb1907 Rookie

Nickb1907

Posted
  • Author
Posted
Thats a lot of stuff and a lot of your answers are already posted on this forum. I sujest your go tothe top of the forum pinned post and read everything from there down for about, well way back on topics. Like the diff locker adjustments are clearly detailed out. This happens to be in the pinned topics part. We will fill in the gaps for you but some of this stuff takes a lot of writing to detail out and it is already done for you. We will be glad to help but go thru the already explained stuff first. There is a lot of good solutions already posted.

Welcome to the forum.

Lenny

I am trying to make my way through a lot of this information. I am trying to tackle the electrical and move on to the rest. Any help with the relay part numbers and locations? I already fixed my 4wd, roof lights, and winch by just moving a relay from one location to another. BTW I would like to see a picture of your supercharger setup. I have read about it but havent seen any pictures.

Thanks

ricksrb Mentor

ricksrb

Posted
Posted

Nickb1907,

Welcome to the forum. Im sure you will find all the info you need as Lenny said. It would also be a good idea to fill in your profile and let us know more about you and where your located. There might be another trooper owner in your area that could help.

Nickb1907 Rookie

Nickb1907

Posted
  • Author
Posted
Nick, If you have a relay I suggest going to Auto parts store and match up the relay. Few of us including myself had to redo the fusebox Sent from my DROID RAZR using Tapatalk 2

The problem I have is I dont trust any of the electrical right now. I have a 20amp fuse plugged into every fuse location and I know that is wrong. I think the relays could be incorrect also. That is why I was hoping someone could give me part numbers. I attached a picture of what I pulled from the manual online. Everything in red is what I am hoping you can help me with. I filled in a few guesses on what the fuse could be based on the color but I was hoping to get some clarification.

Thanks

I am trying to figure out how to attach the picture so hopefully it will show up soon.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • 180gtr
      Parting out Joyner Sand Viper 1100
      By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • RBonds007
      2019 Cub Cadet Challenger 400, trailer to transport the Challenger, and new, never used winch for sale
      By RBonds007
      I bought this SxS brand new.  A couple of years after I bought it, I became disabled.  Thus it has only 47 miles and around 16 hours of use.  I have no need to keep the SxS.  I am in Foley, Alabama.  It is very hard for me to get in out of the Challenger.  I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want  $6500 for the whole set OBO (Serious offers only).











    • Jody Deville
      Joyner 800 Renegade rear axles
      By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...