-
Similar Topics
-
By ita47
I currently have a 2011 Polaris 400 H.O. that has fewer than 300 hrs on it. My buddy bought it new and I bought it with around 100 hrs. I use it around the farm and to get between two properties that are about a mile apart. I am tired of dealing with the choke when its cold or even cool out. It starts fine and runs ok if your driving but until it gets completely warmed up if you pull up to a gate and get off to open it will die. And because of the choke my wife has a hard time with it. Before I got the 400 I had a 2013 polaris 500 midsize that was fuel injected but aways ran rich and foul plugs. I had it at two different dealers and neither one could fix it. So I sold it and bought the 400. My father in law has a 2015 Polaris 570 midsize which is fuel injected and it is hard to start and cranks more than it should. Needless to say I am done with Polaris and ready to sell mine and move on to something better.
I have been looking at the Honda Pioneer 700 and the Kawasaki Mule Pro MX. I was disappointed to learn the Kawasaki Mule Pro MX engine is built by Hysun and not Kawasaki, but that maybe a non issue. Maybe I'm missing another good option that I haven't considered. The main thing is getting something that is bullet proof reliable. Any feedback would be greatly appreciated.
Thanks in advance
-
By Hig
Just purchased a new Axis 700 which was delivered a few days ago. It's May 2023 and I received a 2021 model. Do they upgrade their model years like a car? The Axis 700 was brand new but the model year stunned me.
-
By J R
Hi, I just bought a used 2015 MSU500 with 365 hrs on it. After riding it the UTV seemed sluggish and would not climb a moderate hill without getting a running start in low range. Took it to a repair shop and they told me that the clutches were burnt and slipping. Had the primary clutch replaced and afterwards was told that the compression of the cylinder was only 80psi, which I was told was 100psi below original compression. I've bought all parts necessary, including new crankshaft and bearings to rebuild the motor. My question is, does anyone know if a 700cc top end kit will bolt onto the 500 motor case?
-
By cliffyk
I had mentioned in a previous post that I had removed the front anti-roll bar from my 2020 Outfitter 400; I ran that way for a month or so without noticing any downside however recently I installed a 'suicide knob" (see below) to assist my Parkinson's disease affected arms in turning the beast--but after doing so i found that in the quicker, tighter turns the knob permitted the vehicle would nosedive a bit, dig in, and plow on hard surfaces--not scary, but quite noticeably.
So I put the bar back on. Then today I got about 1-1/2 miles down the main road on the nearby power lines, turned around and came home to take it off--with the bar on, at 25 to 30 MPH, the front-end of the beast jumped like rabbit at each bump in either wheel rut., for a nearly brutal and quite uncomfortable ride. the bar (20 mm solid steel) is far too robust for the weight of the vehicle. The front bar on my 3900 lb. Infinity M37 is 30 mm...
suicide knob--for you younger folks:
-
By Mike L
Does anyone know if you can adjust the front bench seat on an 850-5? I am about 6' 2" and the legroom for me is almost unbearable. My leg begin to cramp after a short distance. I noticed there are what look like adjustable nuts under the seat but I am not sure if they are for adjustment.
Mike
-
-
-
Gallery Images
.jpg.84decc2b5f73a0d00e4b249aedfba113.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.