-
Similar Topics
-
By didgeridoo
Hello, All! I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth. I haven't torn anything apart yet (to diagram), so I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
-
By great8redsfan
Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power. They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil. Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm.
-
-
By Greg Kilgore
I would really like to know what you guys think about this. I'll try not to ramble and make it as clear as I can.
I took this new job with companyX as a fiber splicer a year ago. I have a 45' bucket truck and 10or12 x 8 ft enclosed splice trailer I have to take home. Within the last 6 months all the management in the splice dept left. Now the power/construction management and higher ups are filling in. Just recently we were told travel to our 1st job is not payable even though we are in a company vehicle.
We are union so I asked the union business manager about this. His reply was be grateful you were paid travel as long as you were and that you don't have to drive your POV to the job.
Last week I had 50hr total. The job area is 4-4.5 hrs away. My time was reduced to 44.5 hrs since we were told this travel thing on Tuesday of that week. I wasn't hired for this area. I was hired for area a lot closer to home.
Pay is good. Work is not hard. Insurance is through the union and so far pretty good.
But I hate the thought of having to work extra just to make a 40hr paycheck. Anyone who has to drive as part of their job knows windshield time is not easy.
Anyway what do you guys think. Should I look for a different job or just suck it up because of the decent pay and health insurance.
-
By Steve B
My "R" light on the dash will not go out when I take the UTV out of reverse and put it into any other gear. Is this just the light switch issue or will this effect engine performance in the other gears?
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.