Quantcast
Jump to content


Getting it all running

Zehrungja

By Zehrungja
in Joyner UTV SxS Forum

 Share

Recommended Posts

Zehrungja Newbie

Zehrungja

Posted
Posted

Hello. I recently bought a 2008 Sand Viper 800cc.

I had issues with the starter so I had it rebuilt, however now I cannot remember how it gets wited back up.

If anyone could, would they please inform me through a picture on how to reconnect the four wires I have here. Thank you.

Zehrungja Newbie

Zehrungja

Posted
  • Author
Posted

Sorry, I will when I can. Currently I am out of state, and will return at the beginning of the year. I think I will have to do a good deal more work on this toy since it was left for so long prior to me purchasing it.

  • 1 month later...
Zehrungja Newbie

Zehrungja

Posted
  • Author
Posted

This thing sounds terrific running.

As of now I am trouble shooting the ignition not triggering the start motor to engage. It will spin, but to engage the motor I have to contact the poles on the starter directly.

Also, I am cleaning the rust out of the fuel tank and noticed the baffles inside have come off of the spot welds and are just loose inside the tank.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Rschrem
      2010 700 Hisun starter issue
      By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • Flanman55
      Wiring issues
      By Flanman55
      I have purchased a used Supermach700 (2008), It runs great after a new choke cable but. The temp sensor on the thermostat house is unhooked and can not find where it plugs back in. The fan has been un hooked from the sensor in the rad and cant figure out how it goes back together properly.  The fan was wired to a by pass switch and i just always leave it on but would like to work it properly. I assume the sensor went bad and not changed.
       
      any help would be great.
       
      thanks
    • Gerald Dillman
      2008 Joyner trooper transmission parts
      By Gerald Dillman
      Looking for a output shaft for a Joyner trooper t2. Went to move the buggy after sitting all winter and it appears the out put shaft that drives the rear wheels broke off inside the transmission so looking for the shaft or a complete transmission if someone has one
    • GunnersTacklebox
      2022 Sector 750 EPS starting issues
      By GunnersTacklebox
      Hi All,
      New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)
      It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?
       
      The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while. 
      If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now. 
       
      Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course. 
    • Jon Spruill
      2018 Hisun Sector 1000 Crew stalling but starts right back up. Please help!
      By Jon Spruill
      Hey Guys, I have been chasing a stalling condition for about two weeks now. The bike will crank up and idle fine, then after about 20 seconds it will fall on its face and stall. It happens at both idle and while running at various rpms. You can turn the key off, turn it back on and it will fire right back up without trouble. I have verified spark on both cylinders with a spark tester. I have also added an inline fuel filter, and pulled the injectors to verify proper pulse on each. Things I have replaced - (relearn procedure performed after each component replaced): spark plugs, ECU, relay/fuse box, fuel pump, & throttle position sensor - all with no improvement of the condition. The only warning light I get when the condition occurs is the oil lamp. The bike only has 14 miles. I am at a loss and appreciate any help and suggestions! Thanks

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...