Quantcast
Jump to content


Transmission disassembly how to, any one? Sandviper 1100cc

orlnd03

By orlnd03
in Joyner UTV SxS Forum

 Share

Recommended Posts

orlnd03 Rookie

orlnd03

Posted
Posted

Does anyone know how to take apart a transmission from a sandviper? 1100cc year 2008. I need to change the output shaft. I have the trans out and started to split it in half but something is holding it together.

  • Like 1
Travis Grand Master

Travis

Posted
Posted (edited)

Knock pins are just hollow pins, usually on each side or across from each other. Sometimes you can us a rubber a mallet to tap the 2nd half off, Do NOT use a regular hammer, in case it s aluminum. 

I do not own a Joyner, so I wouldn't trust my into 100%😉

Edited by Travis
  • Like 1
orlnd03 Rookie

orlnd03

Posted
  • Author
Posted

That's a negative travis, I've been working and its too hot in southern California right now to be in the garage. I am going to give it a try this weekend. the goal is to have the buggie ready by October. I've called Joyner 3 times with no luck, they keep saying that the technician is busy and he will call me back but nothing. I just need some basic guidance, I don't want to damage something in the trans trying to take it apart. I'll post some pictures this weekend.

  • Like 1
  • 2 weeks later...
  • 2 weeks later...
Kinarfi Veteran

Kinarfi

Posted
Posted

search using the word transmission, I think I left some info and instructions in here some where, see if you can find it before I have to open up my stored files,

ignore travis, he sticks his nose in where it don't belong and as he said he doesn't own a Joyner and knows nothing about them, but that doesn't stop him from wasting our time reading his dribble. 

Travis, shut the **** up!!!!

  • Like 1
Travis Grand Master

Travis

Posted
Posted

Well, he messaged me back and said he got it pulled apart... PLUS, I was just SUGGESTING WHAT MIGHT be the cause of it sticking. I told him i did not know.  Try thinking before you type? And some show of a "good moderator" by cursing a member out! at least get the guts to do it in Private messages! 

but that doesn't stop him from wasting our time reading his dribble. 

Its your choice whether you read it or not.

 

 

 

orlnd03 Rookie

orlnd03

Posted
  • Author
Posted

Well, I appreciate all the help I can get. After doing the work I realized that the transmission was not difficult to pull apart or fix, very basic stuff. I just didn't want to brake anything in the process. We put it back together yesterday and in the buggy.  This morning after finding an exploded view of the transmission I realized that we put a stop block in the wrong hole, so the trans has to come back out and apart again, which is not a big deal a couple of hours of work will fix that. I'll post pictures of the trans soon. Thank you guys.

  • Like 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Tim n Deb
      2015 Massimo stalled and wont start. oil, new plug, getting gas verified. cranks but does not start
      By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • Joe Breaux
      Oil change
      By Joe Breaux
      Decided to do an oil change on the Massimo ...drained oil, screen was very clean even tho oil wasn't.  Then went to remove old filter.. holy crap ..I tried every tool I have, could not budge it..Went to store and got one of the end cap type..fit nice and tight, put a 1/2 in drive ratchet on it..nope..not moving.  Put a 18 on breaker bar o. It. The inside of the removal tool broke off!!  Had to weld it back together. Put a pipe on the bar for more leverage.  Finally broke it loose..
      I have never seen a filter in my 55 yrs of working on engines so tight..And i was the one who put it on 2 yrs ago.  JUST HAND TIGHT!
       
    • Gerald Dillman
      2008 Joyner trooper transmission parts
      By Gerald Dillman
      Looking for a output shaft for a Joyner trooper t2. Went to move the buggy after sitting all winter and it appears the out put shaft that drives the rear wheels broke off inside the transmission so looking for the shaft or a complete transmission if someone has one
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • Tom Gorski
      2014 Cub Cadet Volunteer Oil Change
      By Tom Gorski
      Just bought a 2014 Volunteer. Can anyone tell me what parts have to come off to change the oil and filter. I can see them but I can't figure out how to access them. Thank You

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...