Quantcast
Jump to content

Long Clutch Cable needed...?


KTMspeedFreak
 Share

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Similar Topics

    • By OviV
      Has anyone found aftermarket side mirrors that work with angled bars on the 800sx other than the super expensive factory ones?
    • By res2fr
      Hello All,
       
       I am trying to find a Scanner that is works for a 2016 MSU500. I found the Tiny Scan TS301 that looks like a decent Scanner but so far have not been able to get confirmation that this works on and older model. It has been stated that it works on the 2019 and newer but not sure about older models. It appears that the ECM/ECU/EFI modules are likely interchangeable between a 2016 and the newer 2019 and on but not sure of the Scanner. I am waiting for feedback from Hisun on this issue right now.
       If this unit is not usable for my model year has anyone found and a Diagnostic Scanner for the older machines, one that works and is Affordable?
      Thanks for reading my post and any information that you may have to share,
      Robert
    • By Mackc
      What type and brands of insulation do you use in the cabin, floor and engine compartment of your Massimo and related 4 by 4 UtVs specially Massimo Buck 400s?
    • By Kristen
      Can anyone help me figure out a part number for a replacement clutch. I have an older bobcat 2200 gas UTV and I have called local UTV/ATV suppliers and they do not have what I need. I was told by one that it would be a polaris clutch but I can not find any information as to which one to order online. 
    • eManualOnline
    • By Zero
      So i have a 2011 EFI 700. the SxS will crank right up everytime without any issues. If i let it run or ride it for about 10 mins it will shut off and then it may turn on if i am lucky but most time i have to let it sit for like 3 hours and then it will run again. i have done the following
      -New fuel filter
      -New injector
      -New spark plug
      -New coil pack and plug wire
      -New air filter
       
      Also could i get a grizzly 660 engine and put in it or would it not work.
  • Similar Tagged Content

    • By Kristen
      Can anyone help me figure out a part number for a replacement clutch. I have an older bobcat 2200 gas UTV and I have called local UTV/ATV suppliers and they do not have what I need. I was told by one that it would be a polaris clutch but I can not find any information as to which one to order online. 
    • By Cozrods
      Today I took my big red to the Honda dealer it felt like the clutches were slipping. The confirmed this and quoted me $5500 to repair. This seems ridiculously expensive. Has anyone else had to replace their clutches. If so what did it cost. Thanks in advance 
    • By Bryan83c
      Need input on compatible clutch sets I can upgrade joyner 1100cc 2018 sand viper with.    Something autozone might carry  and what cars are these chery motors most compatibility with
    • By Gorson
      does anyone have any knowledge of these clutchless automatic manual shift utvs? I have a 4 seater 4x4 650 that the wiring has been butchered and there is no longer a shifter knob. I'm just curious to know if anyone has a wiring diagram or any knowledge of these units without a clutch pedal and are electric shifted and not cable gear driven
    • By alywiski
      I just recently picked up a 2006 volunteer.  It is making a grinding noise that seems to be coming from the clutch or around there.  Sounds like a bering going out.  Trans goes into gear good and it drives good just makes the grinding noise at higher rpms and gets loud as soon as you pull you foot of the gas.  Does anyone know what could cause this or what i need to replace? thanks 

×
×
  • Create New...