Quantcast
Jump to content


Recommended Posts

Posted

Not sure I'm explaining that right. but,.. I'll start with some history.  I bought the 4x4 4010 mule with a bad motor.  I built the engine.  Bottom end up.  Fresh bearings, Pistons, etc.  Cranks up and runs with no issues.  However,.. doesn't seem to run faster than 20 mph and pulses at top speed like something is up with the governor.  It feels like its cutting back.  Climbing and pulling it seems to be fine,. It pulls hard and doesn't cut up.  But on the road flat out  Cuts back/Chugs/pulses/Revs. 

Not sure where to start. Kinda tired of thinking about it. Any Ideas?

Just a mention, I'm not trying to make it faster, just fixed.  25mph it good by me.  Hell,... for my purposes I'm fine with 20 mph as long as its' running properly.

Posted

Welcome to the UTV Board!

 the top speed is supposed to right at 25mph.

First off, whenever i have this similar problem with any engine, i start by running  some carb cleaner through it (pour proper amount or whole can in gas tank)  i usually do half a can for 4 gallon tank. and if that don't work

 i would check your valve clearances, check your manual for specs.

 Someone more experienced than me should come along soon. and will probably have a better idea than me.

 

Posted

So, I've learned some more about this thing.  I bought the SXS from Sunbelt who leases these to construction companies.  I was told they are locked down to 17 mph for construction site work.  I clock 18 mph uphill by GPS.  Not sure how true that is, but my contact there says this is the case.  I don't see any aftermarket device attached like the dynatech thing I've seen.  

Could this be set at the ECM?
Can the ECM be reset to Factory specs?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Frank Mac67
      My Axis 500 has been operating properly for almost a year with Zero problems. While I was away my granddaughter & friends were riding & playing in the snow. They went to the gas station to fill the tank & the vehicle would not start afterwards. I BEEN GIVING MULTIPLE STORIES: The ATV will not start. When I turn the key I can hear the fuel pump come on but nothing happens other than that. 
      - NO CLICK - NO OTHER NOISE
      *I CHECKED THE BATTERY 12.43volts
      *I replaced the solenoid inside the battery compartment. 
      Seems the next electrical component in line has battery connections IN & motor connections OUT with 2 other small wires connectedaswell(I do not know the name of this component).
      Can anyone help?
      I can not find an ordered list of electronic components starting at the battery.
      Can anyone help with this?
      Thanks in advance for any help.
       
    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By Flanman55
      I have purchased a used Supermach700 (2008), It runs great after a new choke cable but. The temp sensor on the thermostat house is unhooked and can not find where it plugs back in. The fan has been un hooked from the sensor in the rad and cant figure out how it goes back together properly.  The fan was wired to a by pass switch and i just always leave it on but would like to work it properly. I assume the sensor went bad and not changed.
       
      any help would be great.
       
      thanks
    • By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • By GunnersTacklebox
      Hi All,
      New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)
      It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?
       
      The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while. 
      If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now. 
       
      Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course. 
×
×
  • Create New...