Quantcast
Jump to content

2009 Joyner trooper valve adjustment


Recommended Posts

The Chery 800cc and 1100cc engines are exactly the same except the 1100cc has an extra cylinder.  Lacking any other info that might say otherwise, the intake is 0.18±0.05, exhaust 0.25±0.05.  I have to presume these are metric measurements since Japan is metric.  I downloaded a service manual for this engine but I can't remember or find the site.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By aefron88
      Since I've seen some questions on this I took some pictures and will provide instructions on a valve adjustment for the UT400. This should be the same for the 550's and other various Coleman/Hisun single cylinder models with the cylinder slanted aft.
      I have seen several people ask of it is really necessary, and read several reports of valves being out of adjustment from the factory. My valves were .004" intake, and .010" exhaust with about 5 hrs on the machine.  I've seen different numbers thrown around for factory spec, but I decided to go with 0.005".
      This is called valve lash. What is is is a gap between the rocker arm and the valve then the camshaft isnt opening the valve. Why does it matter? If it's too large the valve doesn't open all the way, if it's too small the valve dosent close. This can cause valve damage (overheating) as well as loss of engine power (burned fuel is going out exhaust rather than pushing the piston dow).
      Tools required : 5MM Allen wrench, 10MM box wrench, needle nose pliers, flat feeler gauge set, rags
      First you need to remove the fan cover on the passenger side. There is a cooling vent hose on the back side, remove the hose clamp and slide it off. From there there are 4x 10mm bolts holding the cover. The forward ones can be accessed from under the seat.
      Next remove the spark plug from the drivers side. Carefully wiggle the spark plug wire off. Grip it as low as possible and give it a little twisting motion as you pull it off to help free it. Its a tight fit for a socket, but there is a sheet metal wrench in the toolkit that fits it. Unscrew the plug and set it aside. This allows you to spin the motor over freely with no compression to fight. When you reassemble this is a good opportunity to switch to an NGK iridium plug for better performance/less fouling DR8EIX)
      Next you need to remove the intake and exhaust valve covers. The intake us the forward one. There are 3x 5MM Allen screws to remove. The Exhaust is the rear with 2x 5MM Allen bolts. Both covers have O-Rings instead of gaskets and are reusable. When you remove the rear be careful and use your rags as there will be oil that drips out.
      Next up we need to spin the motor over to top dead center. Grab each rocker arm and give em a little wiggle up and down. Spin the engine over by grabbing the fan with your other hand. Spin the engine over until both rockers have some wiggle and are loose.

      Once both rockers are loose slide the feeler gauge in like shown above. Try different feelers as needed to determine your starting spec. You should feel some drag but still be able to move the feeler without too much force.
      If you need to adjust, use the 10MM wrench to slightly loosen the locknut, then with the correct feeler gauge in place, tighten the top square nut while wiggling the feeler in and out. Once you have it right you need to tighten the 10mm lock nut without moving the square head bolt. Once the lock nut is tight recheck the clearance.
      That's it, button everything back up and make sure you have it all reassembled before running it again.
      If you find this helpful give me a thumbs up or comment. If you have any questions or need more help let me know. If there's interest maybe I'll do some more of these
    • By Michael McCandless
      Starter will engage sometimes. Where can I buy a starter and solenoid.
    • By Haskellz
      I have a Gator 550 UTV with two rows of seats and dump bed. I bought new UTV LED lights for front and back and have mounted them on the roof, no problem
      I now need help hooking and running wires from lights to switch.
      Does anyone know someone near Millbrook Al that could do this? If so, please give me contact info.
    • By Huntmastr1
      Hello all,
      I am new here as I am trying to purchase a new to me machine to use on our farm and timber land.
      I am torn between a 2019 Polaris 570 Full size (Windshield and cover)with 1000 miles and a very clean 2013 Polaris Ranger XP900 LE EPS with 2200 miles. Windshield, rear glass, cover, winch, new tires and front shocks.
      The XP900 does cost more but is larger and better equipped. The 570 is priced extremely low which could allow for the accessories to be purchased to equal the 900, but it still would not be the XP900 LE EPS in aminities.
      I am open and gratefull for any advice that can help me get this settled and move on to other things.
       
      Thanks in advance,
      Jeff
    • By johnpeter
      2020 Can-Am Maverick X3 XRS Turbo RR Max On Ebay
      https://www.ebay.com/itm/155930289666?

×
×
  • Create New...