Quantcast
Jump to content

Waco

2006 Cub Cadet Driven Clutch spring tension

Recommended Posts

Does anyone know what to set spring tension to on a Cub Cadet UTV 2006?  

Share this post


Link to post
Share on other sites


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Similar Topics

    • By davisgravel
      I have a 2018 750 challenger, the cooling fan started running all of the time, even with ignition switch off, it will run till it kills the battery.  I've checked the sensor on bottom of radiator, it's an open circuit no continuity, I found 2 more sensors on top of engine at coolant hose, was able to check 1 of those and it's an open switch as well. I can disconnect all 3 sensors and fan still runs. Only way to kill fan is to unplug it just back from fan motor in wiring harness. Any suggestions would be greatly appreciated.
    • By groged67
      I have an issue with my sector crew 750
       2017 EFI
      Starter engages and spins but does not turn the engine over. Does this mean a bad starter clutch. The starter is new. I started the pull of the cover where the starter clutch is located but cannot get to the back bottom bolts.
       
      Any help would be greatly appreciated!
       
    • By Gary T
      I generally use my challenger for light duty misc. use, and for plowing. The one thing I dislike about this machine is the difficulty in shifting. I've had it the shop and they adjusted the shifting lever, but I still have issues. Some times it shifts ok, but the problem is it is hard to get it to move the lever from high to reverse or low to high or from any gear to the other. Seems I always have to accelerate a little to get it to engage to what gear I need it to go to. This is definitely not normal.
    • By Cub owner
      Ok trying again... I have 2018 cub cadet 750. Having clutch issues. Has anyone bought a upgrade for them and where did you get them and about how much. Thanks for any help given. From what i have looked over on here. Lots of nice helpful people 
    • By oldryder
      Cub Cadet 4X4D Trail J466
      Stopped running today, behaved like it was out of fuel.  Low fuel warning lite was not on but I added some fuel anyway.
      When ignition turned on fuel pump noise was different that usual.  Engine would run a bit but "run out of gas" as soon as load was applied.  Fuel filter less than one season old.
      If it's the fuel pump where is it?
      If you think it's something else what might it be?
      Thx to anyone offering advice.  I have a fair amount of mech experience but almost none with diesels.
      mark in MN
  • Similar Tagged Content

    • By oldryder
      Cub Cadet 4X4D Trail J466
      Stopped running today, behaved like it was out of fuel.  Low fuel warning lite was not on but I added some fuel anyway.
      When ignition turned on fuel pump noise was different that usual.  Engine would run a bit but "run out of gas" as soon as load was applied.  Fuel filter less than one season old.
      If it's the fuel pump where is it?
      If you think it's something else what might it be?
      Thx to anyone offering advice.  I have a fair amount of mech experience but almost none with diesels.
      mark in MN
    • By Cub owner
      Ok trying again... I have 2018 cub cadet 750. Having clutch issues. Has anyone bought a upgrade for them and where did you get them and about how much. Thanks for any help given. From what i have looked over on here. Lots of nice helpful people 
    • By Robbie Wyre
      I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles.  I have a slide hammer puller on the inner joint and with all my strength they will not budge.   Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out?   Any suggestions please and thank you.
    • By alywiski
      I just recently picked up a 2006 volunteer.  It is making a grinding noise that seems to be coming from the clutch or around there.  Sounds like a bering going out.  Trans goes into gear good and it drives good just makes the grinding noise at higher rpms and gets loud as soon as you pull you foot of the gas.  Does anyone know what could cause this or what i need to replace? thanks 


×
×
  • Create New...