Quantcast
Jump to content

2005 Polaris Ranger No Reverse

Mac

By Mac
in Polaris UTV SxS Forum

 Share

Recommended Posts

kenfain Experienced

kenfain

Posted
Posted

You'll have to follow that linkage,  physically follow it. Check the lever under the dash n stuff for obstruction, but mostly wherever it ends up.  To see that its clear, and operating properly.  Sometimes branches, and stuff can foul the linkage. Cables can break, or jam. But since yours is catching the forward gears, its probably not a broken cable. It could still be jammed. I'm always pulling branches out from underneath mine. But it all starts there. Where it goes into the transmission, or transfer case, or differential. Wherever it goes.  Make sure its operating the lever, or otherwise working properly. After that, it's mechanic territory. But you have to eliminate the simple stuff first. 

Link to comment
Share on other sites
Mac Newbie

Mac

Posted
  • Author
Posted

Finally found the issue when we got the gear casing out and opened up, it would seem the reverse chain had snapped, resulting in no reverse.   After much swearing and cursing , and waiting for parts, the new chain, we finally had success.   I notice that the grinding sound, which seem to be a problem with a lot of the polarises especially in reverse has now gone.

Changing the chain was interesting as there was nothing on YouTube that tells you how to put the new chain on.  I had to remove both the bearing and the dog engagement face also the gear-33T, 6 face engagement, once you do this the chain will basically slip on into place, you have to do this, otherwise the chain will not go on.   There are some good videos on you Tube that you should watch before attempting to do this.   One last thing, check that the gears are engaging and in the right place before putting the gear case back into the body. 

If I can answer questions regarding this please don't hesitate to drop me a line.

20200106_111750.jpg

  • Thanks 1
Link to comment
Share on other sites
  • 1 year later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Steve B
      "R" light will not go out when the UVT is in any other gear. Is this an issue?
      By Steve B
      My "R" light on the dash will not go out when I take the UTV out of reverse and put it into any other gear. Is this just the light switch issue or will this effect engine performance in the other gears?
    • lonerider98
      2013 UT 500 won't go into reverse.
      By lonerider98
      At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!
    • Hugh
      2018 Hisun Sector Crew 1000 engine die after about 15 minutes run
      By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh
    • Hi sun 500
      2011/14 Hisun 500 fuel issue
      By Hi sun 500
      hello everyone, i just joined this forum to try my luck, few days ago i bought an old (dont know exactly), 2011/14 hi sun 500cc ""carburated"",  was not running at the time, but i fell was a good deal and decided it to bring it home to play with it, this is the issue, i bought and installed a new carb, and pump, i repositioned the battery location and upgraded to a "car batt", reconnected the fuel lines and started it, but it only runs with the choke ON, i checked the bowl, it does have fuel,but for some reason wont inject it to run, i came across a video that say that ""the body small tank had to be connected for the cart to run" (was deleted when bought), sure enough i got it to run sporadically , but the so called ""small body tank'' often runs out of fuel and wont refill itself , i had to couple times do it manually, so how does that small tank works ?..what does it do?..and why if  bypass it , the cart wont start?....any help?..thanks so much!!!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...