Quantcast
Jump to content

Ferguson Fabrication is Closing

UTVBoard News

By UTVBoard News
in UTV News and Information

 Share

Recommended Posts

UTVBoard News

UTVBoard News

Posted
Posted

Ferguson Fabrication is Closing Their Doors. 25% Off Everything.

After 8 years in business we are closing our doors. We feel fortunate for the opportunity to have earned a living doing work we love, and would like to say thank you to all of our customers for the opportunity to serve you.

Now for the sales pitch. We have lots of product left on the shelf and need to sell it before we move. If you have been holding off on purchasing more parts for your side by side, you can save 25% on existing inventory and help us at the same time.

Now thru December 10 25% off everything

December 10-Dec 31 35% off everything

After Jan 1 50% off everything

Look at our website then call 877-Fergfab to order! www.fergfab.com

Ferguson Fabrication specializes in a variety of Performance Parts and Aftermarket Accessories for the Polaris Ranger, Yamaha Rhino, Polaris Razor RZR and Arctic Cat Prowler. We offer Cages, Bars, Rags, Seats, Lights, Canvas Tops, Billet Accessories and more!

View the full article

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Travis
      Mule 550 parking brake cable and rear end work
      By Travis
      The cables are sort of seized up on the emergency brake, they still work but i have to wiggle and pull on em to get them to release, i pulled the drum off but cant see a way to remove the cable. It is kind of dirty inside the drum where it was leaking so i need to run to the parts store and buy some parts cleaner so i can see everything better.
       The shop manual i have  does not cover parking brake cable removal, well.... it does kind of. it says "Remove parking brake cable at both ends" 🙄
       We'll see
       EDIT: ARRR! Looks like my rear axle seal is leaking, there is a small puddle on a machined step below the seal and it smells like Trans oil. felt around the wheel cylinder and it isn't coming from their.....  I guess my weekend is planned for me LOL
    • Hisun .500
      Wiring harness is a mess has anyone ever tore it all out and only put in the basics. Power ,ignition ,starter, stator and regulator
      By Hisun .500
      So my hisun 500 is tore up and all the wiring is wasted i was wondering can i pull out all the wiring and just put in the. Basics .please help
    • Kevin M
      Odes Dominator 800 knocking at idle and jerky in all gears
      By Kevin M
      Hello all. I am new to this forum and new to SxS in general. I recently purchased an 16 Odes Dom 800 with the issue of a prominent knocking noise at idle and it’s very jerky in forward and reverse gears. It does not sound like an engine knock. I bought it cheap knowing about this problem with hopes of it being a cheap and fairly easy fix that I can do myself. Would a bad belt be the cause this symptom? I’m looking for a starting point to begin diagnosing and fixing the problem. I recorded a video of it but am not sure if I can post it on the forum. Any help is greatly appreciated.
    • Hope McCloud
      UT500 grease fittings - have a squeak
      By Hope McCloud
      Does the UT500 need greasing?  Where can I find the fittings?  Thanks. 
    • DIY like a pro! Shop from over 1,000,000 Repair Manuals at eManualOnline.com! As low as $14.99 per manual. Shop now.
    • robwork9
      Massimo T-Boss 410 has lost all electrical power
      By robwork9
      Hopefully someone out there is a T-Boss 410 electrics expert or a Massimo mechanic is viewing this. I parked my 410 and it was working great. I came back a week later and attempted to crank it and nothing. Turned the key and no power. Figured it was a bad/low battery so I charged it. Still nothing. Attempted to jump start it and still nothing. Usually when I put the key in and turn it to the first position, the display comes on and I hear the ECU and other items boot. Now it is doing nothing. 
      I slowly went through the electrical system and found the main fuse attached to the starter relay, part 71602 (pic 1) blown. I figured replacing this fuse would fix my problem. It didn't. I then ordered a new starter relay thinking maybe that part had gone bad and caused the fuse to blow, but a new relay did not fix the problem. 
      I have found a work around for starting the machine. If I take one of the purple/black leads (pic 2) and insert one of them in the bottom right of the starter relay (pic 1 and 3) then the machine will get power even with the key in the off position.  I'm bypassing something but don't know what. I can use my right hand to hold the wire against the lower right of the starter relay, reach over and hold the brake with my foot, then take my left hand and turn the key and it will crank. As soon as I remove the wire from the relay the machine shuts down. I have even removed the power distributor box and it will still get power when I touch the wire to the relay. Of course this is not the way it should work but if I can't solve this problem somehow I may just have to rig a connector to the relay and bypass whatever is causing the electrical issue. Massimo has told me the purple/black wires on my model are not used.
      Any help in figuring what my problem may be or other items I can try?
      v/r,
      Rw
       



  • Gallery Images

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...