Quantcast
Jump to content


Recommended Posts

Posted

i have a 2017 cub cadet challenger 750 camo, after a month of nonstop work with the pandemic i was finally getting a chance to ride it. it would not start, the battery was dead, went to charge the battery and noticed a mouse had chewed a yellow wire one of2 going to a block of some kind in battery box, it is tied into the 2 fuse relay breakers  attached to the starter relay. there is a red with stripe wire that goes to a harness below the rectifier in engine compartment, it has no power to it with multimeter and the fuse block is getting real hot. other than that the dash lights up, but no readout and the gauges dont cycle, the fuel pump does not start. on the fuel pump i checked the red wires to the cdi and both have contact and are intact but one does  not have power when the key is on and there is no spark  i tried starting fluid. i have swapped out the cdi from my cousins  same year and model, also the ecu and the main relay. i have no idea where to look now. his has broke the shim again and will not start. also i did notice that i wiggled a wire connector going to a sensor on the engine and a couple lights came on on the dash, the stirring wheel one and check engine but only did it once and i cant get it to do it again. i have looked over the harness for anymore damage and have found none.

has anyone seen this problem before, is it wiring? ground? what do i need to check next. the place i bought it has no service the guy said he could only swap parts and try. sent me to another place over an hour from me  and that guy on the phone said he was covered up and didnt know when he could look at it so he must be busy lol. besides i dont want to have them charge me $3000 to replace everything on it before they get going.

my advice is do not buy a cub cadet, we thought we were getting a cub cadet and it turns out it is a cheap chinese pos. i still love my cub but wish i had known this before i bought it and i would not have.

any help would be appreciated thanks

  • Alex changed the title to 2017 Cub Cadet 750 camo no digital dash no spark no fuel pump
Posted

ok there is a purple wire that comes out of the middle plug on the fuse box, it goes under the battery box and it splits and goes to the ecu and to the dash, the wire going to the ecu was the problem if anybody ever has this same problem. to check it test for voltage to the ecu on the purple wire then trace back, i hope this can help someone else because i could not find anything on this anywhere. and..................checking electrical problems and wiring sucks 

  • 1 year later...
Posted

Mine is doing the same exact thing and every thing you've done I have done. All I need to do is trace that wire? What should the voltage be at the plug for the ECU?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Frank Mac67
      My Axis 500 has been operating properly for almost a year with Zero problems. While I was away my granddaughter & friends were riding & playing in the snow. They went to the gas station to fill the tank & the vehicle would not start afterwards. I BEEN GIVING MULTIPLE STORIES: The ATV will not start. When I turn the key I can hear the fuel pump come on but nothing happens other than that. 
      - NO CLICK - NO OTHER NOISE
      *I CHECKED THE BATTERY 12.43volts
      *I replaced the solenoid inside the battery compartment. 
      Seems the next electrical component in line has battery connections IN & motor connections OUT with 2 other small wires connectedaswell(I do not know the name of this component).
      Can anyone help?
      I can not find an ordered list of electronic components starting at the battery.
      Can anyone help with this?
      Thanks in advance for any help.
       
    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • By Gerald Mohs
      Is the cam sprocket a bolt removal or is it pressed on? Dang bolt is on tight. Impact wrench won't even move it.

×
×
  • Create New...