Quantcast
Jump to content


Recommended Posts

Posted

I'm having another issue with my 2019 Buck 400. When I push in on the brake and turn the ignition to start nothing happens. If I pump the brake several times it will start right up.  Does anybody know where the relat is that prevents it from starting until you apply the brake? I think it must be loose or something like that.

Thanks for your help.

Posted

I have a 2019 T-boss 410, so it's not exactly the same. However, there's a switch on the brake assembly (usually under the hood) that I needed to adjust, since it wouldn't always start. I would step on the brake, and hit the key, and nothing. I located the switch and adjusted it, now no similar problems. The best thing I can suggest is to follow the brake linkage until you locate that switch. It's the same switch for the brake lights. 

  • 1 year later...
Posted (edited)

Did you locate the brake switch on the Massimo Buck 400? I am having the same problem. I can’t find a switch following the brake linkage. How ever there is a pressure switch on master cylinder. Could this be my problem?

D63BCC81-9583-4FEF-8E72-74DA0973F68B.jpeg

Edited by James strambler
Rephrase question

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • By KWinTX
      I just bought a new 2024 Hison 550 Stryker 2 months ago. this is the second time I have had this issue.  It only has about 20 hours on it. The last time it happened we took it back to the dealer. it was a fuse.  Since we live three-hour time driving there and back. I would like to find another solution if possible.  I have tried all the fuses that seem to have anything to do with starting.  Currently checking the battery. The battery is new. it came with the unit. It is probably 6 months old.  the UTV has all power to everything electrical. lights turn signals and radio all work.  When trying the key to start . it is 100% dead. as in it doesn't even click.  There is a low whirring like the fuel pump is turning on though. The Unit was running and driving just fine.  we shut it down for the night. The next morning my wife found it in this condition.  Thanks for any Ideas or solutions???   Otherwise, it goes back to the dealer tomorrow. Just hope I didn't buy a lemon. Great little UTV when it does run.😅  anyone else ever have this Issue..? 
    • By Homeowner A
      Is there a way to bypass the seatbelt speed limiter?  
    • By Homeowner A
      What's the best replacement battery option for a Coleman UTV 400?  
×
×
  • Create New...