Quantcast
Jump to content


Recommended Posts

  • Alex changed the title to 1100 Joyner Trooper Speed over 30 MPH
Posted

Not enough info to even begin to tell you where to look.  What is the engine RPM when you're traveling 30 mph?  Is the engine running smoothly or acting like it's cutting out, missing or struggling?

Posted

I'm still guessing here.  Since the crankshaft position sensor didn't change anything, that could be the issue.  A bad sensor though would cause rough idle, slow engine resonse when you press on the accelerator, difficulty starting.    Engine starving from lack of fuel caused by a clogged fuel filter; low fuel pressure (should be about 50 psi) or bad throttle body.  A compression test might be of value.  Low compresson on all cylinders could indicate a jumped valve timing belt.  Not likely but it will eliminate one doubt.  3000 RPMs at 30 mph is normal; higher RPMs is not.

Posted

I'm leaning toward lack of fuel.  The engine is needing more fuel that what is being delivered.  Could be fuel pump, filter or the ECM isn't recognizing the demand for fuel from the throttle body.  Other than that, I'm sorry that my skill level is short of what I've suggested.  Good luck on fixing your machine.

  • 2 months later...
Posted

I have a 2008 trooper t2 1100. I changed out the starter and now it will not do the 3 second warm up and start. Are their any shops in California that will still diagnose a Joyner Trooper, or does anybody know which signals can cause the warm up sequence to not go?

  • 5 months later...
Posted

Donald 1968: Did you finally get your issue fixed on your trooper? If so what was the final fix?

California Nut Case: Did you ever find anyone to work on your Joyner, and if not what part of Cali are you in? I am a retired auto mechanic and live 30 minutes from Carson City Nv.  I bought my trooper because it is an automotive powertrain and I know I can fix it, modifying to use more common parts (ie Honda) when I need to. If you are fairly close I may be able to help.

  • 10 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By Jamie 67
      Why is there 2 different length keys for my tboss 1000?
    • By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • By brewski
      I just purchased a 2025 kubota rtv 1100 x cab esd esnting to install light bars on the roof it appears to be prewired for lights how do lights mount and what kind of switches do i need
    • By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
×
×
  • Create New...