Quantcast
Jump to content

2015 MSU 500 Belt

CDT540

By CDT540
in Massimo UTV SxS Forum

 Share

Recommended Posts

CDT540 Rookie

CDT540

Posted
Posted

I need to replace the belt for the clutch.  I see there are numerous off brands on Amazon.  Is there a particular brand that is better than the others?  I have an old CJ7 that I work on a lot and there are certain vendors that sell total junk and should be avoided.  Just checking to see if there are any brands/dealers to stay away from.  I saw a video on YouTube where they used a Gates but I don't see Massimo listed on the parts chart.  If you use 2015 Bennche Big Horn 500 you get part number 21G3353.  Anyone use that Gates belt?

Thanks

Chris

Link to comment
Share on other sites
Greg Kilgore Collaborator

Greg Kilgore

Posted
Posted

Don't have a Massimo. I have a 2013 CFMOTO UForce 600.

But I did order a Gates belt off Amazon.

I went to the Gates website and crossed my part number over to the Gates belt.

All good. 

FWIW, I thought the belt was my issue but turned out to be the wet clutch in my case.

While I had rear of machine up in the air everything worked fine. BUT when I put the rear tires on ground with CVT cover off. 

Had wife put in gear and give a little gas. The nothing wanted to move. This told me the wet clutch was bad. Ordered that off Amazon also. Just don't put the one-way bearing in backward if you have one. 

 

All hope for the best. But the Gates belt are good. At least for me.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • great8redsfan
      2017 Challenger 500 No power on take off or hills
      By great8redsfan
      Okay folks. I have a low power issue. Been like this for a few years. Place I work at bought 3 and all have lost most of the pulling power.  They gave them away after local shop worked on one for 3 months and it had great power for about 1 month and then crap. They replaced throttle body, fuel injector, spark plug and IAC motor. Seat belt switches have wires cut and left open so no seat belt warning light anymore. It revs to 6k rpm in neutral but when put in gear and take off in low it just doesn’t seem to want to go anymore. Running 93 octane fuel with Stabil.  Any ideas greatly appreciated. I dont have a scan tool but no codes on dash. If held to floor it pops a little and runs almost 5K rpm but if I let off pedal about an inch it smoothed out and revs up to 6k rpm. 
    • todd93
      Hisun Sector 550C total electrical failure.
      By todd93
      Hi, all! I. I'm new to the board, hoping someone could help me out! I have a 2020 Hisun Sector 550C that I bought new in 2021. Today, I took some stuff next door to my parents. When I went to leave, I turned on the key, heard the solenoid click, but no lights, no guage activity, no fuel pump, and no starter. 
       
      The battery is good, I checked all the fuses, they are good. Not sure if the relays are good, or even what to look for there. Is it possible that it's maybe a wire? 
      I'm really stumped on this one! Any help would be deeply appreciated! Attached is a pic of the fuse box layout. 
       
      Thanks! 
      Todd 
    • tim hughes
      2021 axis 500 belt issues
      By tim hughes
      does any one else have a slipping belt on the hisun ...i put new wet clutch one way bearing new belt, cleaned primary and secondary and still get slight slippage
    • Keith k
      2015 kymco 450i clutch noise and will not go
      By Keith k
      Just got this kymco 450i Uxv from a guy, drove it around before I paid. Got home drove around town a little while the next day and it started squealing and amd didn’t want to go. Got to looking at the clutch, that’s were the noise is coming from, the primarily sounds like. Maybe a bearing in there cause the grinding noise and it only makes the noise when you go to move.
    • Booker
      Cub Cadet Challenger MX750 Primary clutch issues
      By Booker
      I appreciate any advice anyone can give.
      I am working on a Challenger 750 that the drive belt broke on.
      Removed the side cover and spun the primary drive sheaves. Something was clunking.
      Took it off and pulled the outer cover and all of the rollers were out of their spot and clunking when rotating.
      I noticed these rollers are not round. They have 2 different flat spots on them. Are they supposed to be round?
      If not, How do they go back in? Flat side down, up, I don't know.
       
      I apologize for not explaining this properly. I was just hoping someone has seen this before.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...