Quantcast
Jump to content


Hisun 2009 "clunk"

Geof Rohrlach

By Geof Rohrlach
in Hisun UTV SxS Forum

 Share

Recommended Posts

Geof Rohrlach Newbie

Geof Rohrlach

Posted
Posted

love the forum. We just got a mostly rebuilt Hisun 2009, runs great, no electrical issues yet, however notice a grind and clunk after accelerating and stopping, such as at a stop sign. Sounds like wire caught underneath. We looked it over and only thing that comes close to being in the area is the secondary clutch. Some wear and play noted there. Will replace, but not sure if we are going to fix the problem.

  • 3 weeks later...
aefron88 Community Regular

aefron88

Posted
Posted

Interesting. the shift shaft and driveshaft are under where the secondary is also. I wonder if the shifter adjustment is off, and its popping slightly out of gear, and then popping back in? I'm thinking maybe the grind is it slightly out of gear, and the clunk is it popping into gear under load.

Not sure which model exactly you're talking about? Is it the console shifter or a dash mounter shifter?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • esmarkey
      2018 cub cadet 750 challenger clutch issues?
      By esmarkey
      Hi, I purchased a used Cub Cadet 750 Challenger that seemed like the belt was slipping so I put a new belt in.  It still acts like the belt is slipping but now I am thinking it is the clutch? 
      What is the best way to remedy this problem? 
      Can the clutch be rebuilt?
      Are there aftermarket clutches available? 
    • Burk
      2021 Axis(Hisun) 700 Will not fire up
      By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • HISUN Sector 750 EPS Failu
      Is Your HISUN Loud?
      By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • Hunterman22
      2021 Hisun 500 Axis. Reading Codes??
      By Hunterman22
      Can anyone please tell me or send a link as to how & where to hook up a code reader to my 2021 Hisun 500 Axis.  I have a 6 pin to a 18 pin  adaptor and the blue cord VAG KKL adaptor .Just not sure where or what to hook up to. Can I use your typical vehicle code reader or do I need to download something on a laptop or PC???
       

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...