Quantcast
Jump to content


Recommended Posts

Posted

My Coleman 400 UTV is about a yr old  started it up yesterday parked it outside..later on the day it would not start. Has gas, cranking trying to start but won`t turn over. looked at trouble shooting tips and it said check spark plug. Where is the sparkplug located and any other suggestions

Posted

You say cranking but won't turn over? Do you mean it won't fire, or it won't crank?

First check your battery voltage is about 12.5V, make sure you have fuel in the tank.

From there you can check for spark the spark plug is on the back of the motor under the bed. Connect an inline spark tester and make sure you have spark when cranking.

Then I would remove the fuel injector and verify fuel pulses when cranking.

If all that's good I would check the valve lash & timing.

  • 2 weeks later...
  • 7 months later...
Posted

 My Coleman runs and drives but it loses power when going up a hill is there anything that would cause this to happen? It won’t barely pull itself up hill it runs fine other than this issue.. please help 

Posted
On 7/18/2023 at 2:41 PM, Carrie said:

 My Coleman runs and drives but it loses power when going up a hill is there anything that would cause this to happen? It won’t barely pull itself up hill it runs fine other than this issue.. please help 

I just purchased a 2021 Coleman UT400 and had a similar problem. Now the manual states the grade should not be more than 15%. The hill on my property, and there is multiple ones, is probably around 35%, but I got it to get to the top, about 30 +/- feet or so. I did read in the manual that when going up hill, to put the UTV into 4WD for better traction. I have to try that to see if by having both axles pulling, the UTV will not struggle as much.

Information on climbing hills in my manual is on page 7-10.

I'll update, but give it a try and see if it helps.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By AaronD1982
      Next problem with charging system to tackle, any help would be appreciated.
      New starter solenoid....check
      New Voltage Regulator...check.
      Dynamic test to Stator.....bang...pulling like 2 Volts AC
      Problem: Without pulling the part out and stranding the vehicle at the shop forever.... I am trying to find the correct stator or at least one that might not be exact for the Massimo Buck 400S, but fit and connect and do the job if that makes sense.... if anyone has any ideas, please shoot them my way.
    • By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • By Dave Jones
      So with seat belt on  I can only get up to 20mph then it starts bucking until I get under 20 again. Diconnected the seatbelt and same thing. Reconnected seatbelt and unplugged speed sensor. Zoom..it flies. But now I have no speedometer. I have a new speedometer sensor on the way..any other ideas?
    • By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • By AaronD1982
      I recently purchased a 2019 or 2020 (no manual) Massimo 400S Buck Series UTV.  It ran fine for a couple days but the low battery light was flashing while it drove.  It then died in the field one day and I was able to jump the battery and get it rolling enough to get back to the barn.  It started both times I turned the key for a couple days after and when driven died 10 minutes later in the driveway.  Even after jumping it had no juice, but with the key out of the ignition it kept trying to start, a quick look on the Google machine and it suggested starter solenoid or ignition switch was the culprit.  Fair enough, let's just order a replacement solenoid, right?  No way Jose....the pin connector on the UTV is a 2-pin white plastic connector and the part received is a 4 pin.  How do I swap that and make it work?  Can I even?  Where do I find correct parts in the future?
×
×
  • Create New...