Quantcast
Jump to content


Coleman 550 Loose Timing Chain

Copperline

By Copperline
in Coleman UTV SxS Forum

 Share

Recommended Posts

Copperline Newbie

Copperline

Posted
Posted

I have a Coleman 550 (hisun). Wouldnt start and was sucking instead of blowing through the spark plug hole. Got to the timing chain and it was very loose and for sure the timing was way off. Got the tensioner off and set it to TDC and got the cam gear back aligned. Put the chain back on and set the tensioner as instructed and the chain is still very loose. I extended the tensioner as far as it would go to test and the chain is still loose. 

Any ideas what could be broken or wrong? Why would the chain be so loose?

 

 

  • Alex changed the title to Coleman 550 Loose Timing Chain
Travis Grand Master

Travis

Posted
Posted
9 hours ago, Copperline said:

I think you are right. 

I'm just getting into the process of replacing it and struggling to get the flywheel nut off. 

get some paracord or small rope, remove a spark plug, insert the rope into the plug hole until the cylinder is full (won't take anymore), remove the nut.

i've used this method many many times.

Copperline Newbie

Copperline

Posted
  • Author
Posted

I ended up just fabricating a tool to make it work. A 16" pice of thick steel plate about 4 inches tall. Drilled a big hole about 3" from one end to allow the socket to fit and then two outside holes to put long bolts into the flywheel (I removed two of the flywheel allen bolts). This allows the tool to jam against the frame of the cart and I was able to remove the nut easily with no damage. 

  • Like 1
aefron88 Community Regular

aefron88

Posted
Posted
On 1/15/2023 at 9:54 AM, Travis said:

Wild guess would be that the chain has stretched from heat and wear. Hisun isn't exactly the industry leader in quality parts.

Yep likely stretched. Buy a new chain and compare lengths and I bet the new one is shorter.

Copperline Newbie

Copperline

Posted
  • Author
Posted

I replaced the timing chain as well as the oil chain. Hopefully that does it. Working on this inside the frame has been horrible. I cracked an oil gear tooth trying to keep the engine from turning while trying to get the flywheel off. Two years is really too short of a time to have to be tearing this apart for chains. 

  • 3 months later...
Copperline Newbie

Copperline

Posted
  • Author
Posted

107 hours. 

Make sure you change the oil chain while you are in there.

It was a horrible process. Lots of home made tools because I did it with the engine still in the cart. 

Unreal that the chains are such garbage to crap out at 100 hours. The cart still looks brand new.

Be careful re-fitting the case cover that its flush before you start tightening the bolts. There are so many possible catch points (water pump) that you might think its on and start tightening and then CRACK as you crack the case. As me how I know!

 

 

 

Eppa Wimbish Newbie

Eppa Wimbish

Posted
Posted
16 minutes ago, Copperline said:

107 hours. 

Make sure you change the oil chain while you are in there.

It was a horrible process. Lots of home made tools because I did it with the engine still in the cart. 

Unreal that the chains are such garbage to crap out at 100 hours. The cart still looks brand new.

Be careful re-fitting the case cover that its flush before you start tightening the bolts. There are so many possible catch points (water pump) that you might think its on and start tightening and then CRACK as you crack the case. As me how I know!

Thanks for responding.  The one here shows 200 hrs.  The chain is sloppy loose with the tensioner at full extension.  I've told the owner that it makes no sense to do all the work necessary to replace both chains, as there's no reason to think the new chains will be an improvement over the current ones....  The chain appears to be too small for the application, as it is much smaller than motorcycle timing chains, but about the size of 50cc scooter chains.  In any case, I won't consider trying to do that work with the engine still in place......

 

 

 

  • 9 months later...
TripleBRanch Newbie

TripleBRanch

Posted
Posted
On 1/29/2023 at 6:25 AM, Copperline said:

I replaced the timing chain as well as the oil chain. Hopefully that does it. Working on this inside the frame has been horrible. I cracked an oil gear tooth trying to keep the engine from turning while trying to get the flywheel off. Two years is really too short of a time to have to be tearing this apart for chains. 

Where were you able to find the 2 chains. I found a couple places that have the timing chain at ridiculous prices and one place for the oil pump chain but not SURE it’s the right chain. Ideas?

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • BWF
      Landmaster LM200 Will Not Start
      By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • Dave Jones
      2021 Coleman ut400 rev limiter
      By Dave Jones
      So with seat belt on  I can only get up to 20mph then it starts bucking until I get under 20 again. Diconnected the seatbelt and same thing. Reconnected seatbelt and unplugged speed sensor. Zoom..it flies. But now I have no speedometer. I have a new speedometer sensor on the way..any other ideas?
    • Burk
      2021 Axis(Hisun) 700 Will not fire up
      By Burk
      I have a 2021 Axis(Hisun) 700 from Lowes. Will not start. Checked starter, solenoid, spark plug and fuel pump. Everything seems to be fine. The motor turns over and will try to start but just will not. Battery is also good. Frustrated!
    • HISUN Sector 750 EPS Failu
      Is Your HISUN Loud?
      By HISUN Sector 750 EPS Failu
      "Mrs. Smith" doesn't like how loud our Sector 750 is.  On a HISUN forum someone said the same thing about his 750.  I haven't given it much thought because I've been more focused on stuff that has broken.
      So, I used my decibel meter to check ours out.  4000 RPM, Low gear, under 20 MPH . . . . 97 decibels.  That's above most ordinances, even state boat noise limits.
      AI Overview Ninety-seven (97) decibels is considered very loud and dangerous to hearing with prolonged exposure, roughly equivalent to a newspaper press, a loud nightclub, or a snowmobile. At this level, damage can occur after just 30 minutes, necessitating hearing protection
    • Mitch13
      Coleman 400 wiring help
      By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...