-
Popular Now
-
-
Similar Topics
-
By Mitch13
2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
Gray - seems to carry power
Brown - left turn signal
Green with purple stripe - hazards?
Pink with red stripe - horn?
Green - head lights?
Yellow - head lights?
Yellow with red stripe?
Blue?
Dark green?
There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
Other than that issue, I am about ready to sell this for parts if you interested let me know.
Thanks
-
By RBonds007
I bought this SxS brand new. A couple of years after I bought it, I became disabled. Thus it has only 47 miles and around 16 hours of use. I have no need to keep the SxS. I am in Foley, Alabama. It is very hard for me to get in out of the Challenger. I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want $6500 for the whole set OBO (Serious offers only).
-
By MilSurpYinzer
Anyone decent with electrical work that knows a good tutorial on how to make my running lights switch off all together but also turn back on when I need too? I'd assume that my lights are hard wired to the battery or the fuse panel.
Vehicle is a Kawasaki Krx 1000
I'm looking to ad IR driving lights for night vision and short of just putting black tape over the lights I feel this would be a more efficient option and it would be cooler.
-
By schreib69
I just bought an older (2008) Teryx 750 and am having some concerns. Hoping of course, that most are not too big. . . but more knowledgeable folks like yourselves will surely have some ideas. Thanks in advance.
-- about 2700 hrs, camo version
-- Starting: after not running much at the auction site, I tried it and it was tough to start but half of this was likely I did not quite know the tricks for how long to keep the choke on. However, once it started it was kind of hard to keep running until it warmed up(once warmed it starts perfectly every time with no choke). Now, back to running after the first ignition: I had to hold the RPM's up a bit to keep it running and when doing so it sounded as if a little gnome was inside the engine pounding on something at random intervals. Wondering if this could be detonation-- "knocking"? After warming, it disappeared completely. Maybe just need higher octane gas??
-- After starting and running a bit there was a pretty terrible smell, most "like" burning rubber or an electrical fire. No fire or resolution of this. Eventually this TOO went mostly away, but still basically present. Could it be adjustment needed for the main belt variable speed tranny?
-- When I move from neutral into either Lo or HIGH range forward gears, I get gear clashing. I did NOT put foot on brake and read in manual(just NOW) that you are supposed to do so. (I have NOT gotten back out to check and see if this matters. ) OR, could it be part of the drive system is mashed up??! Geez, hope not.
-- There is a big open hole allowing direct sight into the belt transmission on the back right side. This can't be normal, it must require some plastic cover. Right? Any rodent could get right into the transmission!
-- THere appears to be no muffler or spark arrestor unit. This "could " be the cause of some of the smell. . . ?? but that should not smell like burning rubber or electrical smell. . .
SO. That is all.
I sure would appreciate any insight on this issues and finally(!). . . if I was to take this into a local dealer what would you say are the top three issues I should have them address first?
thanks!
-
By Roadstar515
Does anyone know of a bypass switch or controller. They make one for Polaris which installs into the harness that makes the ECU think it’s hooked up in normal position allowing vehicle to operate normally as if you are wearing seatbelt.
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.