Quantcast
Jump to content


Recommended Posts

Posted

Hi there,

 

My name is Vern and im in Alaska. I have a 2019 ranger 1000 xp HL crew. So the machine had zero issues with clutch or shifting. then the belt blew. i got the new Polaris belt installed with no issues. i cleaned everything and made sure all belt debris was removed. installed new belt.  now it lurches in gear and is hard to shift if at all. when i insert clutch spacing tool in secondary and relieve belt pressure then in shifts when off no problem. the secondary is spinning fast when in park or neutral. i did try adding and removing shims from secondary also without any change.  the primary moves in and out without issue. it appears there is no issue with primary or secondary. im stumped. can u help please.

Posted

ENGINE OFF.  Look at primary (PRI) pulley.....does the belt fit "tight" and rubs on the slider sheave......this is what makes the secondary (SEC) pulley spin in neutral.  Manually spin the SEC pulley.....does it bind and drag at the PRI pulley? 

Options for the problem:

Some aftermarket belts are cut wrong and the inside groves do NOT match the pulley groves and/or the number of groves are different than the pulley groves.  Count both groves and location.

The PRI pulley is NOT opening wide enough.  Did the belt shred with strings?  Sometimes the strings (cords) get UNDER the sliding sheave and bind....keeping the PRI pulley from opening wide enough.

Mechanical wear on the slinger weights, the pins, slides, bad rub wear spots inside...requires PRI tear down and tools.

Remove belt and hand squeeze the PRI sheave.....no binds and pops back to the idle position with a clunk at the stop.

Start motor (no belt installed)  rev up and watch the PRI sheave movement.  Should close up and then slam back at idle.

Posted

Don't know about the ranger. But when I changed the belt on my cfmoto. Once everything was back together I had to spin the secondary sheave backwards 4 or 5 turns. To tighten the belt on the sheaves.

When the belt went out it shredded and bits of cord and rubber was in the primary sheave. Had to clean that out.

Also use a green sos pad to scuff up the sheaves.

 

That's all I got. Best of luck and keep us posted on the progress.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Topics

    • By Skeeter22
      I going from a Yama Rhino and bought a 2026 Ranger 1000XP. I was riding and lost all steering. The steering wheel just spins freely. I have one other video of this happing but has anyone else experienced this.
    • By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • By Cliffampranch
      Hi All,
      I have a 14 mile round trip on level roads to reach the property where I work with my 2025 Amp Crew Ranch (purchased, April 2026).  That 14 mile round trip uses 60% of the battery as shown on the gage for a calculated range of 23.3 miles versus an advertised “up to 50 miles” range.  A mile or two working on the property gets me a flashing gage and warning beeping by the time I get home.  The dealer was good to work with and even with a new battery (yesterday) the results were about the same, although there seemed to be more power and a higher top speed.  I own a Mach-e Mustang so I am familiar with how various conditions affect range, but less than 50% of advertised range just seems like there has to be something out of whack.
      Now I’m wondering if there is a controller and/or software issue affecting the range and performance.  At various points the Amp seems to lose power for no reason and then has trouble maintaining speed.  Any ideas?
      Also, twice now, the brakes seem to have not released fully.  After noticing reduced speed, I stopped and check the rotors and wheel…..HOT!  So, now every time I feel less power, I stopped to cycle the brakes and check the temperature.  Very annoying.  Are there any adjustments to be had?
      And yes, as noted in another post, sometimes the switching from forward to reverse or high to low speed feels sluggish or balky.
      Lastly, while an electric vehicle powertrain is quiet, my Amp was horrible from a road noise and vibration standpoint.  This was easily fixed by locating panels vibrating on other panels or the frame (even the cup holders were vibrating) and installing felt adhesive pads at the contact points (seat to frame, windshield to frame, fenders to frame, etc.).  This is a $10 and 1/2 hour fix that makes a significant improvement in the driver/passenger experience.  Tire noise, yes, but that’s because of the knobby tread.
      I’m trying hard to like my Amp and would appreciate any tips, advice or solutions.
    • By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


    • By Alex
      If you’ve been looking for a chance to score a brand-new UTV, Polaris just launched one of the most unique giveaways we’ve seen in years.
      To celebrate America’s upcoming 250th anniversary, Polaris has announced its Celebrate American Heroes Giveaway, offering one lucky winner a custom-built Polaris RANGER CREW XD 1500 NorthStar 1776 Edition along with an all-expenses-paid trip to Nashville, Tennessee.
      The giveaway isn’t just about winning a side-by-side. Polaris is encouraging people to nominate someone they consider an American hero—whether that’s a veteran, first responder, teacher, volunteer, tradesperson, community leader, farmer, healthcare worker, or simply someone who makes a positive difference every day. Entrants can nominate themselves or someone else by sharing their story and submitting a photo.
      What’s Included?
      The grand prize is a highly customized RANGER CREW XD 1500 NorthStar 1776 Edition featuring:
      Exclusive 1776 commemorative graphics and badging Custom American-themed design package JBL 4200 audio system 50-inch LED light bar Rear winch Additional factory Polaris accessories All-expenses-paid trip for the winner and a guest to Nashville, Tennessee to receive the vehicle in person at the Polaris Dealer Meeting. According to Polaris, fewer than 100 of these special-edition 1776 models will be produced, making it one of the more unique RANGER builds we’ve seen from the factory.
      Why the RANGER XD 1500?
      The RANGER XD 1500 NorthStar sits at the top of the Ranger lineup and is designed for serious work and recreation. With its enclosed cab, heating and air conditioning, premium comfort features, and heavy-duty capability, it’s become one of the most talked-about utility side-by-sides in the industry.
      Whether you’re using a UTV on the farm, around your property, hunting, trail riding, or for work applications, the XD 1500 is one of the most capable utility machines Polaris has ever built.
      Entry Information
      The giveaway is open to eligible U.S. residents 18 years or older. Participants must submit their nomination story and photo through Polaris’ official entry page. Polaris is accepting entries through early July, with the winner receiving the vehicle at a special event in Nashville this August.
      https://www.polaris.com/en-us/off-road/sweepstakes/celebrate-american-heroes/
×
×
  • Create New...