Quantcast
Jump to content


Only stays running when I throttle it dies at idle Colman 400 utv

Richard shepard
 Share

Recommended Posts

Richard shepard Newbie

Richard shepard

Posted
Posted

I have a 2021 colman 400utv engine will start and idle, as soon as you hit throttle to move engine dies and will only start when you throttle it, let off throttle it dies, I replaced the injector and plug still the same, anyone have any other ideas

Rainman Enthusiast

Rainman

Posted
Posted
On 3/9/2024 at 3:15 PM, Richard shepard said:

I have a 2021 colman 400utv engine will start and idle, as soon as you hit throttle to move engine dies and will only start when you throttle it, let off throttle it dies, I replaced the injector and plug still the same, anyone have any other ideas

Did you try and replace the fuel filter? Also, what type of of are you using, as ethanol I believe can clog things up and non-ethanol is recommended.

I also have a 2021 ut400 and had running issues a little different than yours, but in my case I had water in the gas tank. Once cleaned out, problem solved. The problem I was having was that it was hard to start and when started, unless it was totally warmed up, if I stepped on the gas it would stall.

Definitely sounds like a fuel issue ...

  • 2 weeks later...
Greg Kilgore Community Regular

Greg Kilgore

Posted
Posted

Reset the computer. Easy to do. Procedure is

1. With machine off. Turn key to "ON" don't try to start. Listen for the fuel pump to kick on.

2. As soon as you hear fuel pump kick on. Turn key "OFF".

3. Do the cycle of "ON" "OFF" 5 time within 30 seconds. Making sure the fuel pump kicks ons each time. Do NOT start the machine.

4. After the 5th "ON/OFF" cycle. Leave "OFF" for 30 seconds. 

5. Start the machine as usual. 

Also always when starting the machine. The correct procedure is as follows.

A. Turn key "ON"

B. Listen for the fuel pump to kick on, build up pressure, and kick off.

C. Turn key to "START"

Hope this helps.

  • 2 weeks later...
aefron88 Community Regular

aefron88

Posted
Posted

2nd Greg's recommendation. Resetting the computer will zero out all the sensors, IAVV and throttle position, fuel trim, etc.

From there if that doesn't fix it let us know and we can help further troubleshoot.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Popular Now

  • Similar Topics

    • didgeridoo
      Hisun Sector e1 Battery replacement: any tips?
      By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • mike28honda
      Axis 500 cuts out at about half throttle
      By mike28honda
      I have an Axis 500 and never had any problems until now,it cuts out 
      at around half throttle. I changed the TPS with no difference, acts like the seatbelts aren't set but can get up to around 15 mph as long as I don't give it too much gas, thanks for any advice 
    • Nick Varnes
      Bennche bighorn 500 idle issue
      By Nick Varnes
      So I have a Bennche Bighorn 500 that I bought used a couple years ago. Was working fine until this winter when I was plowing and I think it drained the battery. And had a difficult time starting and staying running. Idle seamed really low, and would only stay running if I pushed on the throttle. So I changed the battery, and the acm valve, fuel filter and spark plug it will start up and surgery to 3k rpm but comes back down and dies, unless I give it throttle. I am getting fairly good amount of fuel from fuel pump.  It does spit at stutter right before it dies. What should I try next?
    • Firewalker918
      Anyone customized their uv34XL? Also, looking for seatcovers
      By Firewalker918
      I have a 2021 UV34XL and I am kind of looking to change it up from the orange wheels and maybe do a wrap?  Please share photos of any XLs that has been modified to look better and any seat covers recommended.thanks
       
    • Hoppy one
      Bennche 500, replaced stator no fire
      By Hoppy one
      I replaced the stator on our Bennche 500 because it was not charging. It ran as long as you kept the battery charged. I replaced the stator now it’s not firing. The only problem I found was a wire in the new stator for the crank position sensor was in the wrong place in the plug. I switched it around but still no fire. Putting a meter on those wires and cranking the motor showed no voltage from the crank position sensor. Something I did or a bad “new “ part? Thanks for any ideas.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...