Quantcast
Jump to content


Recommended Posts

Posted

I have a 09 t4 that will not go into 4 wheel drive. I am taken apart the differential but can not figure out how to open the cluster gears!!! Any one can help I would appreciate it very much

I got it open all is good . When I put in 4x4 the you can turn the front axles but the drive line stays in place. Is this the norm on a Trooper. Iam a new owner and a little confused about this.

Tim

Posted

There are some past postings on here about the front diff, how it works and how the 4x4 engages. You will have to do a little searching. Most of the post were by Lenny. Do a search for front diff Lenny. He may even read this and post again or PM (Private Message) you. Kinarfi and a couple others may even chime in.

rocmoc n AZ

Posted

First go to Technical Articles above and look for Differential inspection. My first thought is that is is in the actuator. There is a collar that connects two gears together by sliding from all the way on one gear to half over each gear thus connecting them and engaging lockout. If this collar doesn't slide far enough to get over the second gear (it really wants to get half way over it), lockout won't engage. Likewise if the collar slides all the way onto the second gear, it's going too far and you won't be engaged here either. The pin that goes into the side of the diff controls this and its range of movement is adjustable under the dash and at the diff.

Lenny

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By Mitch13
      2022 Coleman 400 with 13 hours on the engine and the mice got to it. Every wire coming out of the steering column in one cluster has been eaten through. I tried reconnecting matching wire colors to each other and I get the left turn signal and hazards to work, nothing else. If I play around a bit I can get the horn to honk or headlights to come on but only when I connect them to the brown wire. Obviously I don't know what I am doing here. Does anyone have a picture of how these wires are connected when they are under the hood on the drivers side coming from the steering column?
      Gray - seems to carry power
      Brown - left turn signal
      Green with purple stripe - hazards?
      Pink with red stripe - horn?
      Green - head lights?
      Yellow - head lights?
      Yellow with red stripe?
      Blue?
      Dark green?
      There is also a bundle hanging under the hood not connected to anything green with yellow strip, brown and blue?
      Other than that issue, I am about ready to sell this for parts if you interested let me know.
      Thanks
    • By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

    • By MilSurpYinzer
      Hey all, I was just wondering what you guys consider a necessary upgrade or spare part to have or mod onto your machine.
      I'm going for a kind of shtf survival rig that's not going to be SUPER heavy and I'm looking at getting:
      A spare belt (I keep seeing this mentioned everywhere I look so it must be important)
      A spare tire and mount( So would I need a jack like one from an old jeep or something else?)
      Tire chains for the winter
      And maybe a cargo bed upgrade so things don't slide out.
      Bumpers because duh.
      I already installed high output lights and have a windshield, roof, back window, and winch. And I outfitted a Molle panel for the back of my passenger seat with extra supplies like food, first aid, and spare mags.
      Any advise on increasing durability, longevity, and having something on hand because it's absolutely necessary would be a plus.
      Thanks so much!
    • By dragon
      I need help I have a 2016 Kubota 1100 RTV my tilt steering wheel locked in the upper position after using the side release. The handle works but does not release the steering wheel to a lower position. If anyone knows and easy fix, please let me know any help is appreciated. Be Safe, Thanks!
×
×
  • Create New...