Quantcast
Jump to content


Recommended Posts

  • Replies 38
  • Created
  • Last Reply

Top Posters In This Topic

Posted

2030914850104282158ZqXxTd_th.jpg

When I added my surge tank, I moved the fuel pump up next to the filter and also moved the pressure regulator, I also opened the gauge of the regulator and cleaned the dust out and then sealed it when I put it back together.

The gas tank has 2 outlets at the rear of the tank, if you are headed down a steep hill with just a half tank of gas, the outlets will be above the gas and the fuel pump will promptly be starved for gas and the pressure will drop and the engine will die. The lower the gas level, the less the steepness of the hill required for this to happen. A SURGE tank is a small tank the that is used to feed the fuel pump so this does not happen, mine has a low pressure pump to keep it full and the return from the regulator returns to the surge tank. This is an idea that was borrowed from snow mobiles.

Kinarfi

Posted

Never checked it....Turned it down and it was fixed lol...Something is not correct cause I wouldn't think you should be able to change how much injectors spray with fuel pressure.... And also the purge tank sounds like a great idea...Gotta look that one up on how yo do that...

Posted

Never checked it....Turned it down and it was fixed lol...Something is not correct cause I wouldn't think you should be able to change how much injectors spray with fuel pressure.... And also the purge tank sounds like a great idea...Gotta look that one up on how yo do that...

The higher the fuel pressure, the higher the volume of fuel that goes to the engine. The injectors are open for a specific time. At higher fuel pressure, more fuel can get thru in that same amount of time. The computer attempts to adjust it based on the O2 sensor output, unless its not hooked up, but it is still limited to how much it can adjust. Most everyone on this forum runs generally from 50 to 60 pounds fuel pressure. I'm not sure that the injectors will run properly at 30 psi. They do have a min and a max pessure they need to run properly. At low pressure, they don't atomize the fuel correctly and at higher pressure, the computer can't control the volume because injector output becomes somewhat earatic at above about 75 psi. You may want to try another fuel gauge. When mine was stock, it wouldn't even run below about 40psi. Kinarfis solution for running out of gas uses a storage reservoir tank, called as surge tank, that is kept always above a specific level so the fuel pump always has a fuel supply. I did the same thing by using a sump in the bottom of my tank. The sump also acts like as a storage reservior or surge tank. The idea is to create a reliable source of fuel when the Tropper is on a slope. There are a variety of ways to correct this issue. Some are more complex then others. I use an accumulator for smoothing out or eliminating surges in my fuel pressure.

Lenny

Posted

The higher the fuel pressure, the higher the volume of fuel that goes to the engine. The injectors are open for a specific time. At higher fuel pressure, more fuel can get thru in that same amount of time. The computer attempts to adjust it based on the O2 sensor output, unless its not hooked up, but it is still limited to how much it can adjust. Most everyone on this forum runs generally from 50 to 60 pounds fuel pressure. I'm not sure that the injectors will run properly at 30 psi. They do have a min and a max pessure they need to run properly. At low pressure, they don't atomize the fuel correctly and at higher pressure, the computer can't control the volume because injector output becomes somewhat earatic at above about 75 psi. You may want to try another fuel gauge. When mine was stock, it wouldn't even run below about 40psi. Kinarfis solution for running out of gas uses a storage reservoir tank, called as surge tank, that is kept always above a specific level so the fuel pump always has a fuel supply. I did the same thing by using a sump in the bottom of my tank. The sump also acts like as a storage reservior or surge tank. The idea is to create a reliable source of fuel when the Tropper is on a slope. There are a variety of ways to correct this issue. Some are more complex then others. I use an accumulator for smoothing out or eliminating surges in my fuel pressure.

Lenny

I will Have to check mine...Seems like it is running correctly and smells fine...Not to rich..I think I will pull the plugs and see what they are.....

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Similar Topics

    • By didgeridoo
      Hello, All!  I've decided to replace the traction batteries in my 2018 Sector E1 with a 48V Lithium set. They may be expensive, but I figure the Discovery Dry Cell are, too. I am not looking for the max driving range, as I have never received near the brochured range to begin with, but a good mix of charge/ get work done/ charge is what I am expecting.
      I have settled on the 48V EAGL kit from bigbattery dot com. Each battery pack provides 30Ah. The kit ships with a charger, as well. The packs would be physically connected in parallel (using a busbar) to one another, maintaining the 48V voltage, but together would be able to provide the amp draw the buggy pulls when going up hill or towing a rake (rated 320 max continuous Amps). This is in comparison to the serial connection the eight 6V lead batteries. Each of the EAGL batteries looks to have its own BMS; am I correct in thinking I will have to use their included charger rather than (simply) changing the onboard charger to lithium mode? The chemistry of the pack is LiFe PO4, for what it's worth.  I haven't torn anything apart yet (to diagram), so  I am not sure how the dash will interpret the AMP draw, but the kit I am looking at includes a dash mounted charge indicator.
      If anyone has completed a similar conversion, do you have any tips? Specifically, how did you remove the original batteries, and how did you secure the new ones? I am guessing that almost any change from the stock batteries would involve at least some modifications. Any tips would be appreciated, especially things I may have failed to consider. Thanks!
    • By mike28honda
      I have an Axis 500 and never had any problems until now,it cuts out 
      at around half throttle. I changed the TPS with no difference, acts like the seatbelts aren't set but can get up to around 15 mph as long as I don't give it too much gas, thanks for any advice 
    • By Nick Varnes
      So I have a Bennche Bighorn 500 that I bought used a couple years ago. Was working fine until this winter when I was plowing and I think it drained the battery. And had a difficult time starting and staying running. Idle seamed really low, and would only stay running if I pushed on the throttle. So I changed the battery, and the acm valve, fuel filter and spark plug it will start up and surgery to 3k rpm but comes back down and dies, unless I give it throttle. I am getting fairly good amount of fuel from fuel pump.  It does spit at stutter right before it dies. What should I try next?
    • By mfitzner
      Cranks after installing a jumper wire to ignition switch to get power but will not start
      Have spark and fuel pump runs
       
    • By Jeff freeman
      I have a Coleman 550.  Was having problems to start with where it would start and then shut off after a couple tries. It would take off and be good. It then got to a point where it would not start at all. I replaced the fuel injection twice the second time I replaced it I noticed a mouse or something had chewed one of the wires that connect the electrical to the fuel injector. . So two-part question first does anybody have a part number for that wire harness?  Second, any other ideas after I fix the wire harness permanently on what could keep it from starting I have gas flow up to the fuel injector.


×
×
  • Create New...