Quantcast
Jump to content


FUBAR

Spur of the Moment
 Share

Recommended Posts

Kinarfi Veteran

Kinarfi

Posted
Posted

Check out the difference between a Trooper tranny and a Viper tranny, look the the 2nd photo above and compare to this one, My guess is that it gears the Trooper up because of our differential between the wheels on Troopers that the Viper does not have. Just a guess, any one know for sure what the extra gears are for?
Kinarfi

photo removed, needed the space elsewhere, Kinarfi

  • Replies 32
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

ricksrb Mentor

ricksrb

Posted
Posted

Check out the difference between a Trooper tranny and a Viper tranny, look the the 2nd photo above and compare to this one, My guess is that it gears the Trooper up because of our differential between the wheels on Troopers that the Viper does not have. Just a guess, any one know for sure what the extra gears are for?

Kinarfi

Viper only has 4 gears and trooper has 5th?

Spur of the Moment Enthusiast

Spur of the Moment

Posted
  • Author
Posted

Took the buggy out yesterday and WOW. Actually turns. With the straight gears tight turns in the dirt were impossible and highway turns were hard steering. Now on asphalt I can do a tight 360 almost with one hand and handling in the dirt is fantastic. I wish I did this when I bought this thing over a year ago. Thanks to all who help me through this rebuild.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Topics

    • mike28honda
      Axis 500 cuts out at about half throttle
      By mike28honda
      I have an Axis 500 and never had any problems until now,it cuts out 
      at around half throttle. I changed the TPS with no difference, acts like the seatbelts aren't set but can get up to around 15 mph as long as I don't give it too much gas, thanks for any advice 
    • Hoppy one
      Bennche 500, replaced stator no fire
      By Hoppy one
      I replaced the stator on our Bennche 500 because it was not charging. It ran as long as you kept the battery charged. I replaced the stator now it’s not firing. The only problem I found was a wire in the new stator for the crank position sensor was in the wrong place in the plug. I switched it around but still no fire. Putting a meter on those wires and cranking the motor showed no voltage from the crank position sensor. Something I did or a bad “new “ part? Thanks for any ideas.
    • Thearm
      TW 450 dies on steep hill
      By Thearm
      I have a 2018 TW450 that runs fine on flat ground but dies out when under load going uphill. Changed the gas filter and spark plug with same results. Letting it set for a few minutes it will run until it hits a incline. Belt is not slipping, but the engine just dies out and doesn't even want to run in neutral. Any ideas as to what I can try is appreciated in advance. Also only run non-ethanol for fuel.
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...