-
Similar Topics
-
By Toofast4you
I have been working on variations of the Clutching for the 6 Arm design and have had Outstanding results . The Test vehicle is a 21 Turbo RR completely stock. All changes are in the Primary Clutch . The 6 Arm clutch made more power than the P Drive (stock) after the 6 Arm was properly calibrated. Here is the final Dyno pull . This is the stock clutching vs. the Prototype Kit . Very Impressive ......Just wanted to show that you can get plenty of performance out of the 6 Arm clutch and not buy a P Drive . In Fact , i tweaked a P Drive and The Graph was almost identical when both clutches were ran ....Both of these clutches were ran on the same machine ....
-
By Dabadoo
So I have a new(ish) 2020 Coleman outfitter 550. It came from TSC with 10hrs and needed some work. After changing the choke solenoid, spark plug, fuel injector and battery, it ran great! However after a hard rain storm, I went out to start it and the dash lit up as normal but there was nothing from the engine. I heard what I think was the starter click but nothing after that. I ordered a new starter just in case, but does anyone have any other idea of what it could be? I assume something that should not have gotten wet, got wet but I have no clue as to what. I also checked the fuses, and nothing blew.
-
By robwork9
Hopefully someone out there is a T-Boss 410 electrics expert or a Massimo mechanic is viewing this. I parked my 410 and it was working great. I came back a week later and attempted to crank it and nothing. Turned the key and no power. Figured it was a bad/low battery so I charged it. Still nothing. Attempted to jump start it and still nothing. Usually when I put the key in and turn it to the first position, the display comes on and I hear the ECU and other items boot. Now it is doing nothing.
I slowly went through the electrical system and found the main fuse attached to the starter relay, part 71602 (pic 1) blown. I figured replacing this fuse would fix my problem. It didn't. I then ordered a new starter relay thinking maybe that part had gone bad and caused the fuse to blow, but a new relay did not fix the problem.
I have found a work around for starting the machine. If I take one of the purple/black leads (pic 2) and insert one of them in the bottom right of the starter relay (pic 1 and 3) then the machine will get power even with the key in the off position. I'm bypassing something but don't know what. I can use my right hand to hold the wire against the lower right of the starter relay, reach over and hold the brake with my foot, then take my left hand and turn the key and it will crank. As soon as I remove the wire from the relay the machine shuts down. I have even removed the power distributor box and it will still get power when I touch the wire to the relay. Of course this is not the way it should work but if I can't solve this problem somehow I may just have to rig a connector to the relay and bypass whatever is causing the electrical issue. Massimo has told me the purple/black wires on my model are not used.
Any help in figuring what my problem may be or other items I can try?
v/r,
Rw
-
By Byron Johnson
Does anyone have a had time starting there utv.
I have a T-Boss 750 and I have had to put 2 starters in and put heavier wire to the starter but it still has a problem starting. it will turn over and than die before it wil turn over again. could it be that there is to much compression that might cause this problem
Thank you
-
By Brianmart95
I recently purchased a new Kubota RTV520. When i try to start it i have to do the cold start procedure every time. Once it is running for a few minutes i can restart it without any issues.
The cold start procedure is turn the key to start position and let the fuel injection system turn on and stop. Crank for 10 seconds and if the unit doesn’t start, turn off and repeat the process 30 seconds later.
If it hasn’t been used for a week and i try to start it i have to repeat the cold start procedure at least 3 times until i get a successful start.
The dealer says this is normal and its not a malfunction on the engine. I feel like its weird for a new machine to have this starting routine.
I live in south Texas so the weather is not extremely cold.
Is ANYBODY having this problem? I am contemplating returning the UTV but i want to know if this is a common problem with the new 520 model.
-
-
-
Similar Tagged Content
-
- 1 reply
- 1,071 views
-
- 0 replies
- 2,151 views
-
- 0 replies
- 2,493 views
-
- 0 replies
- 2,308 views
-
- 0 replies
- 2,601 views
-
-
Gallery Images
.jpg.20223437086d05b33428002722c88a8d.jpg)
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.