Quantcast
Jump to content

2510 mule not running right

tree farmer

By tree farmer
in Kawasaki UTV SxS Forum

 Share

Recommended Posts

tree farmer Newbie

tree farmer

Posted
Posted

I have a 2000 mule 2510 that idles great but spits and sputters and generally doesnt have any power. I have changed the plugs, cleaned the carb, changed the fuel filter, blown out the hose going into the gas tank, and drained the gas twice which had some sediment in it but still cant get it to run right. Any ideas?

Link to comment
Share on other sites
  • 1 month later...
xcycle Rookie

xcycle

Posted
Posted

Did you check your needles/jets for wear when you cleaned the carb? They may need replaced. Or check to make sure your choke is working correctly. It idleing fine but sputtering and not having much power suggest to me an air/fuel mixture problem...that there is an air restriction or fuel delivery problem. The only other thing I can think of is the coil not firing consistantly.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Steve B
      "R" light will not go out when the UVT is in any other gear. Is this an issue?
      By Steve B
      My "R" light on the dash will not go out when I take the UTV out of reverse and put it into any other gear. Is this just the light switch issue or will this effect engine performance in the other gears?
    • Travis
      Kawasaki Mule 550,520,500 Complete service manual
      By Travis
      View File Kawasaki Mule 550,520,500 Complete service manual
      This is a complete service manual for the Kawasaki Mule 500,520 and 550 models.
      Topics  covered include Brakes, Steering, Electrical system, suspension and fuel system. As well as engine repair procedures and Transmission/Final Drive procedures.
       
      ********************************************************************************************************************************************************************************************
      If you need more information about the engine this manual linked below is chock full of information.
      Thanks goes to @cliffyk for getting these files all  into one PDF format for uploading.
      Submitter Travis Submitted 04/18/2021 Category Kawasaki  
    • nods
      2022 sector 750 GAS powered: Codes E-113, E-108, E-123, E-132, E-650. What are these?
      By nods
      Less than 40 miles can barely start. Dealer is working with Hisun on a number of other issues on this UTV. Can not get clear info on the meaning of these E codes this is getting. Anybody have some clear info for me?
    • lonerider98
      2013 UT 500 won't go into reverse.
      By lonerider98
      At the end of last year my Coleman UT 500 will not go into reverse. I can hold it over toward the reverse to move it nut it won't lock into reverse. Anyone have this problem? Winter is just about over and going to have to get this resolved. Thank You!
    • Nathon S.
      Bennche 700 EFI Bighorn New Fuel pump not working
      By Nathon S.
      I have a Bennche 700 EFI Bighorn. I’ve recently been unable to get it to start. After a little troubleshooting I realized my fuel pump was not pumping fuel. This weekend I emptied the gas and replaced it with new. I replaced the fuel pump, fuel filter and fuel injector. I also replaced the battery, spark plug and made sure all my fuses and relays were good. I have confirmed that the float on the fuel pump is not obstructed. The UTV is about 12 years old and has less than 100 hours on it. It has not run in over a year.  Not sure whats going on?!? After doing a little reading I'm leaning towards it being an issue with the ECU or perhaps a faulty wire in the wiring harness. Anyone have any ideas on where to start looking or what I could be dealing with? Any help is appreciated, thanks in advance!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...