**Wanted** Kawasaki Mule Drive clutch/pulley removal tool
-
Similar Topics
-
By RBonds007
I bought this SxS brand new. A couple of years after I bought it, I became disabled. Thus it has only 47 miles and around 16 hours of use. I have no need to keep the SxS. I am in Foley, Alabama. It is very hard for me to get in out of the Challenger. I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want $6500 for the whole set OBO (Serious offers only).
-
By Andy Dickerson
So heard the grinding noise on the drive shaft a couple of times while going down a steep hill. Never heard this before going down the same hill. I already knew about the splines wearing out because of improper heat treating so I went through the process of removing the shaft to just replace it. A lot things need to be removed to get that thing out. Once I had it remove I didn't see any wear on the splines but what I did notice was the rear spline to rear differential had ZERO grease i.e. it was completely dry and I could see rust that had developed on the shaft splines and inside the differential mating surface. The front of the shaft where it connects to the transmission was well greased. Both ends of the shafts have springs in them with the rear spring being multiple times heavier which would force the shaft to mate securely into the transmission. Unless of course the rear is rusted and starts sticking which is what I think was happening. If the rear splines begin to rust and it starts sticking and the spring doesn't have the enough force to overcome the sticking because of the rust, the shaft will not get fully seated into the transmission. If this starts happening frequently it will eventually eat up the front splines on the transmission side shaft splines which is exactly what I see in the pictures of stripped splines.
I don't know why the rear spline shaft wasn't greased but this would cause it to eventually stick. I have been concerned about this ever since reading about it so as soon as I heard the grinding I stopped driving it. Thankfully there wasn't any wear. I'm wondering if this was deliberate or just laziness by the assemblers. It makes no sense not to grease it. The repair manual that I purchased from motorcycle doctor specifies to grease the splines. Both shaft ends have a rubber seal meaning there's is supposed to be grease in there.
I used to have a gold wing and there is a special grease required for the rear drive differential which happens to be a spline shaft setup. They use a lithium grease with moly. I had purchased a couple of tube of Magnalube-gx that I never used as I sold the bike. The Hisun manual recommends using a lithium grease which doesn't have the additives of a lithium moly grease that is specialized for spline shafts. Per magnalube website. "Magnalube-GX, however, uses a proprietary matrix of advanced polymers, molybdenum disulfide, and PTFE, so it stays where you put it without getting pressed out, while also maintaining a low frictional drag."
Anyway, long story short everything is back together and no noise. I would recommend those that haven't checked the grease in the splines on both ends to do so before the shaft get destroyed. Especially If you have heard grinding. Those rubber boots can be pulled back without having to take to many parts off. If you've been hearing grinding then there is probably significant wear already and time to replace the shaft and grease it properly.
-
By Rocahaja
Dumb question probably but what size drive chain is used on Massimo gunner 250? I believe it to be 520 but not sure. Thanks for helping
-
By Bill L
I have a 2022 sector 250 with a side ways engine. Both chain drive gears are missing teeth. The drive gear on the transmission shaft and the driven gear on the chain drive shaft. I have the part numbers but they are not to be found anywhere. My dealer contacted His in and their reply was not available. It was just out of an extended warranty. Any ideas? I wonder what they would have don't if still under warranty.
-
By Racing Dreamz
We're looking at the Axis 750 at Lowe's. It's the one with the two flat screens in the dash board. The Lowe's store tells me there are no "Service Centers" for them in our area(upper east Tennessee). Now, I've had Chinese products before, namely the ODES 650 UTV. It was a real piece of crap. Are these worth the $12,000 or should I go somewhere else. I like everything about the Axis 750 but skittish. I was told back in October of last year that Axis has not provided any Service Manuals on these models at all. And that the usual UTV repair places won't touch them. Anyone that has these, what kind of issues have you had? What should I look out for, just in case? Thanks in advance. :)
-
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.