Quantcast
Jump to content


Roll Cage

plumber

By plumber
in Joyner UTV SxS Forum

 Share

Recommended Posts

plumber Proficient

plumber

Posted
  • Author
Posted

Looks good. Now you will have a little extra piece of mind. The v bracing is a must if you are using the stock cage. Be sure to send us a pic when you are all done.

2scoops, Thanks yes I will be doing the v up front and a few more things. Yes that's why I done it there are some hills I don't even try because I didn't think the cage would hold up. I'll should have it done by this weekend I'll post more pictures.

  • 2 weeks later...
plumber Proficient

plumber

Posted
  • Author
Posted

off subject but did you flip your intake and how did you do it

toddlong. No I didn't flip my intake I bought the bottom part of the intake. All SQR 472 engines comes with this intake on them except the trooper. How I like it I think it's better than the fuel controller. Just bolt it on my motor and it made my A/F gauge go up by .6. If you look at the picture it's fatter than the ones joyner has on it. Here's the part number or my be you can fine a used engine to get the part off of it. It just bolts right on. .DLJ.472-1008013

.

post-178-0-61427100-1410040122_thumb.jpg

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • SkyPilot56
      working on a coleman 550 out fitter
      By SkyPilot56
      working on a coleman 550 out fitter , had a shit load of codes, coil, injector , and the map sensor for fuel injector replaced all 3 and figured it would start , but no joy have spark (new plug also and inline fuel filter) cleared the codes and still have the engine light , turns over fine but damn thing still will not start, friends daughters were driving it and turned it off to park , and went back to start it and same thing turns over but will not start , with this machine anyone have any ideas as to what the hell , I should be looking for , no plug's unplug checked wires none seem to be pulled apart or broken !
    • Karlibob
      2020 Tracker 800 sx front end noise
      By Karlibob
      I have a 2020 800 sx with about 16 hours on it.  From day one I have heard a clunking noise from the front end going over bumps.  Has anyone else experienced this?  Also this past weekend while out riding I heard a noise that sounded like the dump bed bounced three or four different times, again has anyone experienced anything like that.  Thanks, gary
    • A P
      2022 Hisun Sector 550 eps. Power steering not working
      By A P
      Hi
      I have a 2022 hisun sector eps 550. 30amp fuse is blown for eps. Checked the motor and it’s fine. Opened up the controller and found a bad diode. Dealer wanted 500$ for the controller. Just posting this in case it helps someone. I couldn’t read numbers from the old one so just took a guess and replaced it with a 100v 3amp diode. 
    • clint501
      Hisun E1 charger not working
      By clint501
      I recently purchased a Hisun E1 and the other day the charger stopped working properly. The LED on the dash blinks red & green and the light on the side of the charger also blinks red & green. The fan on the charger does not come on like it used to do. There is no error code that I can see. Does anyone have any suggestions to remedy this?
    • Robbie Wyre
      2005 Cub Cadet side by side front axles
      By Robbie Wyre
      I'm working on a 2005 Cub Cadet side by side and I'm trying to remove the front two axles.  I have a slide hammer puller on the inner joint and with all my strength they will not budge.   Anyone have the same issues and is there something I'm missing or a trick of some sort to pull these out?   Any suggestions please and thank you.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...