Quantcast
Jump to content


Gas leak from intake of carb after setting long time

Flesh

By Flesh
in Joyner UTV SxS Forum

 Share

Recommended Posts

Flesh Newbie

Flesh

Posted
Posted

2007 Joyner 650 Sand Spider, has carburetor leak out of intake after sitting for a long time, I was going to take it off the intake manifold, but found that nuts are real hard to get to, started to think I need to remove it with the intake manifold, but not sure about the gaskets, I do not have any, so this may turn into a problem I don't want, but the gas is just pouring out as fast as the fuel pump can pump it, I was hoping it would stop after a while, as if maybe the float was stuck, and that gas flow would free it up, but no such luck today, maybe tomorrow I will try it again, so my question is has anyone deal with this issue, and is there an easier way to fix this?

Should I buy a gasket kit before starting this, do I take the carb apart and clean it, if so will I need a kit to put it back together?

Not sure what carb is on here, besides the stock one, I have no manual that tells me what it is, XIANGLI UU276M CSHI0E GO4 is all I can find on it, and the letters are real funky, like they were written by hand with an electric scribe.

Thanks

Flesh Newbie

Flesh

Posted
  • Author
Posted

Do they make a kit for it, this unit has very low hours, and its just gummed up, I will take it apart to see if I can clean it, but I need to know about the availability of gaskets, and do I take it off the intake manifold, or pull the intake manifold, which seems to be a lot easier.

I do not have the money to buy a new Carb, a $150 would take a year to save up, I am a Disabled Gulf War Vet living off Disability, I just want this to get around my property, and go down to the river near by.

Flesh Newbie

Flesh

Posted
  • Author
Posted

Update: I thought if I just let the fuel keep flowing it would stop, and it did, just to let anyone else with this problem know, I just removed the filter, and put a bucket for it to run in, and eventually it stopped.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Gerald Dillman
      2008 Joyner trooper transmission parts
      By Gerald Dillman
      Looking for a output shaft for a Joyner trooper t2. Went to move the buggy after sitting all winter and it appears the out put shaft that drives the rear wheels broke off inside the transmission so looking for the shaft or a complete transmission if someone has one
    • Ed Michael
      Older Landmaster LM 650 Fuel Problem
      By Ed Michael
      My older LM 650 is blowing fuel into the air cleaner.  Any idea on what would cause this?  It is the Suzuki motor.  Not sure what model year it is.
      Thanks
      Subaru SxS.mp4
    • Mmcleary
      Textron Stampede leak
      By Mmcleary
      I have a 2018 Textron Stampede that has a leak on the passenger side rear end. Definitely looks like a gasket has gone bad, but I’m not sure what fluid I’m replacing?  
    • Hunterman22
      2021 Hisun Axis 500 No Start - Need Help Please
      By Hunterman22
      2021 Hisun Axis 500 UTV (From Lowes)
      Will NOT START
      MY apologies if this is to much info just wanted to give yal the most information possible for help.
      I'm a so called diyer. An Electrician by trade 21yrs. I got my S×S from my last job. The contractor purchased this S×S for this specific job brand new, from Lowes. They used it for hauling materials, tools, & a little bit of anything you can think of on an Industrial type job site. 
      I remember getting on the SxS one time & pushed the gas petal all the way to the floor & SxS had very little power. 
      So anyway ,when the job finished up back mid July this year (7/2024) , I asked the contractor what they was going to do with it. I was told to take it. Otherwise it would go to the contractors yard (storage yard) & most likely rust away. 
      Took it home washed it , it had a heavy coat of dust on it & in it dust was every where. My helper & I had to push it on the trailer to get it home.  After washing it throughly I let it sit & dry out for a good day and half, maybe 2 days. Before trying to start it. NO START. Will turn over & try to start but thats it. 
      So here's what I've purchased & installed. New Air Filter, new spark plug, new air idle control valve (AICV), new throttle position sensor, new throttle body, new oxygen sensor, new digital dash speedometer/fuel gauge/clock. 
      Also drained the old oil & gas & replaced with new oil & 93oct. gas. I should probably mention that I've changed the AICV twice. The 1st time I changed the AICV I was able to get the SxS started & let idle for at least 10-15min. Drove out of the garage, with very little power,  turned it around & barely got it back in the garage.That was the one & only time I've been able to start the SxS. I've also cleaned the Throttle Body and & intake with TB cleaner.  So after that the AICV was  making weird noise so I pulled it out & tried cleaning it, pretty sure I messed it up. So I purchased a Throttle Body that came with new AICV & TPS. Still NO START.  I've checked the fuel pump & the fuel injector.  I took the injector off still hooked up to wiring & turned the key over, the injector sprayed a lot of gas out kinda the size of a volleyball. I've also checked the clearance gap on the intake & exhaust valve. But today 11/2/2024 I'm going recheck spark plug gap & the valve gaps. And alot of other checking. Would the driver side seat belt have anything to do with it not starting?? I know the driver side seat belt has to be in gauged for full throttle "going fast". Thing is the drv. side seat belt will latch but feels like might be messed up inside of it. Tired opening it up but to no avail.  I've never had a S×S or 4wheeler so I was really excited when I got the S×S,not so much anymore.  I work on & fix my own vehicles usually no problems.  But this SxS is kicking my ass.
      So if possible & someone could help me with some ideas or tell me what Im doing wrong or did wrong, I would greatly appreciate it.  Thank you for reading thus far.
       
       
    • Blair
      Major Cabin Intake Noise Reduction
      By Blair
      Most of us complain about the ridiculous noise in the cabin. My wife likes to ride but the noise is a major downer. You can’t even have a conversation without shouting at each other. Well, I manage to reduce the cabin noise by approx 200%!

      I addressed the intake that is poorly placed right between the driver and passenger. First, I cut the air filter inlet pipe in half (pic 1). I then reinstalled it upside down (pic 2). I then attached a flexible intake tube (pic 3) and directed it behind the cabin (pic 4). Major difference.
       
      Then I covered the interior engine cover with Dynamat extreme and then 200 mil Chaogang sound deadener / heat shield mat on top of that (pic 5). Since I cut off the intake and redirected it, I completely closed off the intake (engine fence) so no engine noise can come thru (pic 6). It also reduced the heat approx 50%. I did leave on the heat mat that came stock on the engine cover, so it has 3 different mats. It was a snug fit. Major difference again.

      My wife rides all the time now since we can have a conversation when we ride. Major improvement to my riding experience. Thought you might like to check it out.


















UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...