Quantcast
Jump to content


Bad Bad News for my Trooper T2

bigdan120

By bigdan120
in Joyner UTV SxS Forum

 Share

Recommended Posts

bigdan120 Rising Star

bigdan120

Posted
Posted

Well fixed the rear locker cable and put new tie rods on. My buddy that helps me went for a ride down the slate dump to make sure it was locking and unlocking. Well he went to come back home and went up a hill and heard a Bang! Well let's say it pretty much stopped itself and wouldn't move from the hill. He ran to get me and I went to look....

Yeah....... here it goes!

The rear end must have broken inside and locked up.

This is not where it ends.

It locked so hard that it actually broke the shaft stub off coming out of transmission to the rear drive shaft.........

Yep its prob going to be setting awhile....

Sad Day for me....

silverbullet Experienced

silverbullet

Posted
Posted

silverbullet

Sorry it seems like the ring and pinion locked up.Pull the differential out and open it up and see if case is damaged.If not i think some one on the UTV forum has one for sale.The shaft in the trans is easy to replace and not to expensive.If you need any help send me and email.Or call 928 344 2117 ask for Matt.I have ring and pinion if you need it.Its new so see if some one has a used one it will be a lot less.

bigdan120 Rising Star

bigdan120

Posted
  • Author
Posted

Thanks Guys! I'm going to maybe look into somethings when it's apart and see about motors that might bolt up. And maybe a different rear end. I don't know if it's me or what but I'm tired of this rear..

This makes 3rd time iv had it apart..... after yesterday I don't think it's going to be very good outcome when I pull it apart....lol

Kinarfi Veteran

Kinarfi

Posted
Posted

Thanks Guys! I'm going to maybe look into somethings when it's apart and see about motors that might bolt up. And maybe a different rear end. I don't know if it's me or what but I'm tired of this rear..

This makes 3rd time iv had it apart..... after yesterday I don't think it's going to be very good outcome when I pull it apart....lol

Is that all, LOL, I don't even bother to unbolt the housing any more, I just pop the inner CVs and pull the allen heads holding the right side cover on and pull the ring gear assembly out, but I did adjust clearance on previous removals. Now that my radiator is up where the spare tire was (sort of) and the spare tire is hanging off the rear of the engine cover bed, it's even easier to do.

Jeff

silverbullet Experienced

silverbullet

Posted
Posted

Silverbullet

Matt is the parts man.He is on vacation will be back on Tue.I am standing in for him till tomorrow.And is just the owner i have retired i had to take it back from Jose because he could not make the payments.What i can say is we have been buying from China direct.So we can some times get parts from China that Joyner has stopped making.Older models 650 Commandos 800 cc Viper 650 spider.We will carry all these parts + the new up dated parts.Meaning you more options.Like the ring and pinion for all the models front and rear.We are the only Joyner dealer with the 650 commandos rear differentials in the world.Hope this helps you under stand my position.Retired!!!!!!!!.By the way we due have the front differential 690.00

  • 4 months later...
Ricky Chuck Rookie

Ricky Chuck

Posted
Posted

Is that all, LOL, I don't even bother to unbolt the housing any more, I just pop the inner CVs and pull the allen heads holding the right side cover on and pull the ring gear assembly out, but I did adjust clearance on previous removals. Now that my radiator is up where the spare tire was (sort of) and the spare tire is hanging off the rear of the engine cover bed, it's even easier to do.

Jeff

  • 3 months later...
  • 4 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Popular Now

  • Similar Topics

    • Thearm
      TW 450 dies on steep hill
      By Thearm
      I have a 2018 TW450 that runs fine on flat ground but dies out when under load going uphill. Changed the gas filter and spark plug with same results. Letting it set for a few minutes it will run until it hits a incline. Belt is not slipping, but the engine just dies out and doesn't even want to run in neutral. Any ideas as to what I can try is appreciated in advance. Also only run non-ethanol for fuel.
    • rdc
      Looking for the left side shaft carrier where the rear bearings go for a 2014 1100cc sand viper, I understand an 800 cc carrier will also work.
      By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • Fmaxiron
      Honda Pioneer 1000-6 back windshield or screen.
      By Fmaxiron
      I just purchased a 2023 Honda Pioneer a couple of weeks ago and had the hard roof and a front Honda Pioneer windshield installed at the shop before taking ownership. As things are drying up here in NC, the grass and dust are beginning to fly right through the back of the cab while driving. I was wondering if anyone has any good recommendations on rear windshields, dust panels, or mesh screens to help stop this?
      Thanks a lot!
    • rdc
      Looking for a left rear shaft carrier (just the carrier) for a 2007 Joyner 1100 sand viper
      By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • MilSurpYinzer
      New Mexico etc
      By MilSurpYinzer
      I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
      Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...