Quantcast
Jump to content

Everdata

Joyner C2 Commando 650 - Looking for Front Drive Shaft

By Everdata, in Joyner UTV SxS Forum

Recommended Posts

Everdata    0

Everdata
Posted

Hi, I'm trying to find a front drive shaft for C2 Commando. Does anyone know where I can find one? Or if there is a replacement part from something else that would work?

Thanks all for your help

George

Share this post

Link to post
Share on other sites


Everdata    0

Everdata
Posted

Hey Bogdan, when I bought the commando, someone took it out. They didn't say anything, I also found out that the front diff was blown.

Hey Matt, would a trooper or a renegade front drive shaft work in the commando??

Thanks

George

Share this post

Link to post
Share on other sites




Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
Go To Topic Listing

  • Similar Topics

    • Lenny
      Front Ball Joints need checking
      By Lenny
      I'm not trying to trample flatbeds post about the front ball joints being able to pull out. I just couldn't find his post to reply there. Sorry flatbed. Flatbed found that the bolts holding the ball joints in place weren't close enough to the ball joint stem to fit into it's groove, thus the ball joint could work it's way out. This happened to flatbed and Kinarfi. It could be very dangerous if this happened at the wrong time. I finally got around to checking mine today. The top of the ball joint on the front left had already pulled out 1/8". The bottom one was still ok. I did as flatbed sujested and drilled them out and refitted them with new bolts. Both joints on the right side did not need any work as they were secured ok by the original bolts. To reiterate what flatbed said, be sure to address this potential failure. Just redo them and don't wait for signs of them pulling out.
      Lenny
    • farmcrew
      Looking for Commando 650 steering rack boots
      By farmcrew
      I recently got a 2007 Commando 650 C4 and I'm in the process of going through it from stem to stern. The AZ sun has really taken it's toll on all the plastic and rubber. One CV boot is torn and the others are probably not far behind. Most of the rubber on the control cable ends are on bad shape and the steering rack boots are almost completely disintegrated. Anyone have a source for the steering rack boots?
    • TmJoyner
      2016 Sand viper 1100 front suspension rattle
      By TmJoyner
      New to the Joyner community.  Bought a used 2016 1100 sand viper in descent shape. Only 155 miles.   Runs great.  It just rattles quite a bit in the front when riding on rough gravel / hard-packed dirt roads outside St Johns.  Removed front wheels and seems to be coming from both upper and lower suspension arm bushings/radial bearings (see pic); both left and right.  Seems like some play inside the eyelets - as I shake the arms a bit.  I assume it's not supposed be loose in there like that and the bushing/bearings are worn.  Anyone have had this issue and how did you go about changing them?
       

    • Terrypenton
      2008 Joyner Renegade 800 R4 all gages except speed and tachometer don’t work
      By Terrypenton
      Bought this machine a couple years ago and the gages didn’t work.  I have troubleshot this thing numerous times to no avail. Thought it may be a common ground so I individually grounded  the gages, didn’t work.  I have tested the sending units.  All have some resistance that changes as the engine revs or gets warmer.  Please help me.  Thanks in advance


UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH


  • Automotive Webmaster
×
×
  • Create New...