Quantcast
Jump to content


2008 Renegade 800 cc

Technician!

By Technician!
in Joyner UTV SxS Forum

 Share

Recommended Posts

Technician! Rookie

Technician!

Posted
Posted

New to this site, been lurking for a while. Did some searches, but no luck so far.

I am investigating the purchase of a 2008 Renegade, and was wondering what model specific problems I should look for.

Tech forum was helpful, and I am technically astute (hence the name), but have never owned or worked on one of these. I currently own two King Quads (1993 and 1995), and love the drive/differential selection available to me. This is why I feel the Joyner is the only UTV I will consider at this point.. But like MOST makes, there are always some common "weak links" that only owners and users know about.

I was hoping someone experienced with this model could help me out.

Thanks!!

silverbullet Experienced

silverbullet

Posted
Posted

Silverbullet

The weakest part is the differentials.If you open the fill plug on the rear deferential look up to see the bolts that hold the ring gear.If it has wire going threw the bolts you should up grade the differential if it has tabs than it has been up grader.This dose not mean you will not have a problem with differential but at least it was up graded.The rear drive shaft should have C/V joints not have universal joints.This will at least some one took care of the drive train.This is the worst things that fails.Cut off the bands off the C/V boots and clean out the old grease and replace with a good C/V joint grease.if you want to ask a question just call 928 344 2117

Thanks Matt

Technician! Rookie

Technician!

Posted
  • Author
Posted

So if the diffs aren't the updated style, where are parts available to do an update? Or can I dis-assemble it and do any mods to the existing diffs to prevent the common failure?


By the way, what is the common diff failure here?



As far as CV's vs. U-joints, I presume you are not referring to the rear axles, but the single rear driveshaft, correct?



Thanks so much!!


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • AlphaSerenity
      Hisun Axis 500 Problems - Hesitation, struggles to go up incline, and low speed regardless of gear range
      By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • HighSon
      Some recent Hisun Sector 750 mods
      By HighSon
      Haven't posted in a while since solving the excessive cabin noise issue, so I thought I would share a few upgrades to my Sector... Realize that this is driven daily on the street, so some of the mods are to make it more streetworthy.

      Locking gas door.

      Rear view mirror.

      Modified windshield for better airflow in cabin.

      Lowered and modified headrest bar for improved rear view.  Tailgate protector.

      Folding armrests.

      Overhead utility rack.  Keeps the interior cooler and dryer, too!

      Folding rear seats.

      Dust cover and seat protector.
      If anyone wants links to the rear view mirror, seats, or arrests, let me know and I will post.  But know that everything requires some level of fabrication.  The utility rack was all custom built.  Cheers!
    • Jody Deville
      Joyner 800 Renegade rear axles
      By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
    • mike.s.
      Kawasaki mule model 2010, 4x4, gas motor, sell or trade
      By mike.s.
      SOLD 
       
       
       
       
    • KMP
      2015 Arctic Cat Wildcat Sport 700 XT (tips for maintenance / just purchase)
      By KMP
      We just bought our 1st side-by-side and wanted to get tips on maintenance items we should address immediately for our 2015 Arctic Cat Wildcat Sport 700 XT.  We are truly beginners and welcome any and all suggestions.  Thank you, we appreciate your help!

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...