Quantcast
Jump to content


Trooper T4 No Spark

Countryboy59

By Countryboy59
in Joyner UTV SxS Forum

 Share

Recommended Posts

Countryboy59 Rookie

Countryboy59

Posted
Posted

Does the Trooper T4 need to have the fuel pump running and build pressure before the Ign. has spark?

I bought a used T4 that ran when it was setup 4 years ago. Drained gas tank.

Checked for spark at plug wire, None! Did not hear fuel pump run when cranking.

Does it have spark even without fuel pump in operation. I checked all the fuses they are OK.

I do have the manual.

post-3653-0-18906700-1463533842_thumb.jpg

  • 1 year later...
Dan B Community Regular

Dan B

Posted
Posted

I have an R2-1100cc witch is almost like a trooper with a different body style. After I turn the ignition on, I have to wait about 3-5 seconds for the gauges to cycle before I can start the engine.  It probably has something to do with the ECU "booting" up.  I don't think the ECU gets power until the ignition switch is in the "ON" position.  Like the computer you are using now, you can't turn it on and use it until it boots up.  At least that'w what makes sense to me.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • Kierobi
      MSU 500 Fuel Pump Ground
      By Kierobi
      Have a MSU 500 that we got from my wife's uncle a while back. We've had it running and hauling around the property but it stopped a few months ago after what I thought was running out of gas and I'm just getting to looking into it. 
      Had fuel to the injector but nothing coming out the injector so swapped with new injector and installed inline filter in the supply hose from fuel pump. Tried again and still nothing but noticed this time that I can't hear the fuel pump priming. 
      Pulled off the electrical connection and I'm getting 12V to the fuel pump but it won't run. Put it on a test bench and got it to run so put test lamp between +ve and -ve terminals on the connector and nothing. Checked against the passenger seat securing post and get a light. 
      Tried chasing the wire back and think that the ground is through the ECU but not 100% sure. Can someone confirm for me? And if it is through the ECU, is the ECU just grounded against the frame or is it wired through to the battery?
      Thanks in advance and hope this all make sense!
    • RBonds007
      2019 Cub Cadet Challenger 400, trailer to transport the Challenger, and new, never used winch for sale
      By RBonds007
      I bought this SxS brand new.  A couple of years after I bought it, I became disabled.  Thus it has only 47 miles and around 16 hours of use.  I have no need to keep the SxS.  I am in Foley, Alabama.  It is very hard for me to get in out of the Challenger.  I would like to sell the set, 2019 Challenger 400, trailer and uninstalled winch (this was bought brand new as well, someone was supposed to help this newbie install and we never got around to doing this). I want  $6500 for the whole set OBO (Serious offers only).











    • Butch
      2023 Hisun Axis 700 fuel problem
      By Butch
      I have a AXIS 700 EFI Fuel pump pressure stays at 40 psi and when return line is blocked the pressure goes to 60 psi. and wll only run with return line closed. 
    • mike.s.
      Kawasaki mule model 2010, 4x4, gas motor, sell or trade
      By mike.s.
      SOLD 
       
       
       
       
    • MilSurpYinzer
      Altering running lights
      By MilSurpYinzer
      Anyone decent with electrical work that knows a good tutorial on how to make my running lights switch off all together but also turn back on when I need too? I'd assume that my lights are hard wired to the battery or the fuse panel.
      Vehicle is a Kawasaki Krx 1000
      I'm looking to ad IR driving lights for night vision and short of just putting black tape over the lights I feel this would be a more efficient option and it would be cooler. 

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...