Quantcast
Jump to content


Recommended Posts

Posted

Hi I have a 2008 Joyner Renegade that died and will not re start It had been sitting for about 2 months while I waited for a new rear diff and then finally found time to work on it. It started OK after I filled it with gas and charged the battery. It started and ran for about 5 minutes and died I pulled the outlet line off the fuel pump and am getting lots of fuel the engine It has electrical power to all circuits as near as I can tell. Any schematics I have found are microscopic and when you expand them they are written in Chinese. I found one fuse box at the right front frame Who knows what the fuses are for They are not identified on the panel or cover. I replaced one fuse and all others were good I found some fuses and 3 relays tied up behind the battery Switched relays around and made no difference. There is a huge 40 amp fuse in line I cleaned the corrosion off the terminals on it. I still have the same issue It is cranking over, has fuel delivery to the engine but is not firing

Is there another relay/fuse panel I am missing? Does the system use a TPS and or crankshaft position sensor that could be the culprit?

Does anyone know of an on line service manual for this beast

Thanks for any assistance

  • 3 months later...
Posted

Did you check the coils with a spark tester? I just worked on a buggy that would start and only run a few minutes and then die. Chased the ghosts for weeks. Turned out it had a weak coil and it would spark pretty good on the first crank then the spark became weak or intermittent and would die. New coil and it runs fine. 

  • 4 years later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      I posted this before , but I had the year wrong. The part I need is for a 2014, I don't know what all years will work, but I need the 2 bearing style with the spacer in the middle. It looks like this pic. If anyone has one I'll buy it rite away. my email is [email protected]. Thanks, RC

    • By BWF
      I have a 2011 or so Landmaster LM200.  I cannot get it to start.  I turn the key and nothing happens.  The brake switch seems to be working, the ignition switch works.  The Coil is new the Voltage Regulator is new and the starter relay is new.
       
      I can connect the terminals on the starter relay and it starts right up and runs fine.  I just can't get it to start by turning the key.
       
      I am having a bit of trouble bleeding the brakes, not much fluid comes out at the calipers when I am pumping the brakes, though that an air bubble near the brake switch might make it not sense that the brake pedal is depressed.
       
      I am at a loss, please help!
       
      Brad
    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By MilSurpYinzer
      I heard there's several off road festivals out that way. One or two post apocalyptic, the rest just rev and run. Anyone know a good one that offers camping? Any advice for out of state people like hauling, legality, and where to stay?
      Ideally me and the missus would be down for camping out and setting up shop somewhere nearby. That way we can just wake up, load up, and ride.
    • By Sidewinder
      All mid 2008 through 2014 Polaris RZR 800 series have a big problem with the rear differential pinion nut backing off, allowing the pinion gear to shoot into the rear differential, destroying the rear differential. This has happened with machines with as little as less than 100 miles on them! Reports indicate that there are no problems, nor warnings, until the rear differential grenades, locking the rear axles solid! This requires the machine to be lifted onto a trailer, to be transported for rear differential replacement, as it destroys the case. After failure, rear differential replacement can be quite expensive: labor alone can run from $800-$1200 and a new OEM Spicer rear diff, if you can find one, can run from $1700-$2500! So, if you own any Polaris RZR 800 series between the years of 2008-2014, I recommend that you do this repair before further use of your machine. personally, I have grounded my machine until it can be done. Please check the online post for your own awareness.

×
×
  • Create New...