Quantcast
Jump to content

BORN TO BURN. The New Generation Of Spark Plugs.


Travis

Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Irons
      Hopefully this helps somebody because I couldn't find any info on this runaway condition.

      Drove 1/2 mile to the gas station and when I started up to leave the starter stuck on. Turn key off starter is still running~! Limp it home wondering what the heck to do, get it in the garage and pull the negative battery terminal to get it to stop. Whew, WTF?

      Calm down and start checking things, starter is hot of course but nothing is smoking and nothing smells burnt. Pull battery cover off and start checking wires from battery to relay and relay to the starter. OK good nothing is hot, nothing is crispy and nothing is melted. Probably smoked the starter though. If this had happened to my wife and I wasn't around the machine would have run until the battery died and probably melted down/burned.

      I'll get to the point to save you folks some time and trouble. Because this is a kymco machine you need 2 different Kawasaki parts to make this repair, and information is scarce to say the least. The switch and a sub harness to connect it to the machine's plug.

      Everything works now, but the starter sounds horrible so I'll be changing that too before spring.

      Good luck out there and hopefully this is just a freak occurrence, but if I were you I'd get rid of this kymco part and put the Kawasaki replacement in now.

      Switch, Magnetic is part number 27010-0767
      Sub Harness Start Relay is part number 26031-Y034
       
       

    • By FloridaMan
      I have a 2012 Massimo MSU 500 that died. I found that it didn't have spark and the fuel pump wouldn't run. Checked all fuses and none were blown.
      Went through and replaced the ignition coil, HT lead and spark plug. Still no spark.
      Thought it could be the fuse/relay box because I didnt' know much about the machine at that point so I replaced it. No spark.
      Then I replaced the ECM just because I was running out of ideas. No spark.
      I removed the 9 pin connector and hardwired it making sure that they were no wires got swapped. Still no spark.
      Then I replaced the wiring hardness. In doing so, I replaced the 9 pin connector with new ones. I made sure all wires were matched up between the engine harness side and the other harness assembly. Still no spark.
      I have no other ideas what to do. My fuel pump doesn't kick on and I have no spark. I have 12V on the fuel pump, ignition coil and fuel injector, but no ground from the ECM control.  I unplugged the fuel injector and waited for a diagnostic code but nothing ever came in. It makes me think that the ECM isn't powering up. I've checked for 12V on pins 18 (purple wire) and 15 (white and black wire). I also checked for ground on pin 2 (black wire). All are good.
      I am out of options here and I have no idea what else it could be. I have all connections redone and are coated with dielectric grease. I've checked all easy things like fuses and making sure I have 12V in the right placed. I would appreciate any help.
    • By ILoveOldJunk
      Recently acquired a 21 year old Mule.  The previous owner let the brake master cylinder run dry, and when I flushed the brakes, one wheel's brakes locked up.  I took the wheel off, but cannot get the axle nut off, and there is not enough space to get my gear puller behind the drum anyway.  Anybody had an issue with seized brakes?  How can I get this thing off to replace it or rebuild it?
    • By Oldman
      I installed a new GY6 150cc engine in a Bull Dog Pup 200 and when I put it in drive, it grinds for a second and then runs fine.  Works great when i place it in reverse.  Could it be from it idling too high?   Any help would be greatly appreciated.
      Thanks!!!!
    • By NicholasNWM09
      Hello Everyone,
      COOL NEW Product Alert! 
      A company called NEW Wire Marine or NEW Wire has Badass custom panels for UTV, Buggy/Hunting trucks. From Fully wired switch panels with laser etched rockers with backlights in 5 different colors, to just parts like voltmeters, phone, USB and 12 v chargers. Rockers can be printed, or custom laser etched rockers and they even have sleek labeled pushbuttons. They are a first-class company with a great knowledgeable staff and outstanding customer service. Switches are based on 12v or 24v circuits and they also have marine grade wire and connectors, which is perfect for waterproofing your system!
      Go check them out!
      Check out the websites : https://newwiremarine.com/ and https://rockerswitchpros.com
       
       
       
       
×
×
  • Create New...