Quantcast
Jump to content

2016 Hisun 750 cab heater installed - $175

Rangerider45

By Rangerider45
in Hisun UTV SxS Forum

 Share

Recommended Posts

Rangerider45 Apprentice

Rangerider45

Posted
Posted

I installed a Maradyne Mm-a1090002 cab-heater in my Hisun.  It was a fairly simple install with the most difficult part being to find the proper location for the heater body.  It has to be located so that the heater hose, etc is not blocked by OEM air filters, body frame, etc.  On my 750 Sector I determined that by centering the heater body a few inches directly below the gauge cluster worked perfectly.  The 5/8" heater hose comes out just to the right of the air filter tube.

Since the firewall is plastic, I placed a large piece of stainless steel on the outside of the firewall for a backing plate.  I drilled a couple of 1" holes in the plastic firewall for my 5/8" heater hose and spliced them into the upper and lower radiator hoses. I spliced the upper heater hose into the upper radiator hose and the lower heater hose into the lower radiator hose.  No shutoffs, since I figured I could easily install them later if I need them.  I bought 8 ft of 5/8 heater hose and 8 - 1" hose clamps at the auto parts store.  Then I bought 2 pex tubing tees 1" X 3/4" X 1" at the hardware store to splice into the upper/lower 1" radiator hoses.

The electrical is easy by running the black ground wire and red hot wire to the power supply (cigarette lighter) in the center dashboard.  By removing the power supply you won't have to drill large holes in the dash and you have the correct wiring needed to wire the heater switch.  I installed another power supply below the front of the bench seat in the middle.  I did that because it's easy for the driver to access and it was near the battery box for an easy installation.

After I refilled the radiator overflow with anti-freeze, I pulled the Hisun's front wheels up on my trailer with the back wheels on the ground.  I did that so the radiator and overflow bottle were higher than the rest of the cooling system and any trapped air bubbles in the heater core would head for the overflow.   If that doesn't work, let it idle with the upper radiator hose clamped shut (needle nose vise grips) directing all the coolant towards the heater core to speed things up.  Remove the vise grips when the radiator fan turns on and then put them back on when it shuts off two or three times.

I have about $175 invested for parts and heater for the project, and my heat laser reads 190 degrees when the heater is on.

20171014_140409.jpg

20171015_105222.jpg

20171015_112615.jpg

20171015_105015.jpg

20171015_105444.jpg

20171015_105612.jpg

20171015_105701.jpg

20161206_221047.jpg

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Similar Topics

    • AlphaSerenity
      Hisun Axis 500 Problems - Hesitation, struggles to go up incline, and low speed regardless of gear range
      By AlphaSerenity
      Hello,
      Before I invest $10k+ into a brand new UTV for the farm, I want to get my feet wet with a fixer upper and learn the mechanical side of things. I acquired a 2022 Hisun Axis 500 (Lowes-specific model) from an auction for $500. It has only 200 hours and 120 miles on the engine. It looks like the previous owner used it for ranch work and didn't drive it on trails, deep water/mud, or anything too crazy.
      While it runs and moves, it has some problems. It struggles to accelerate up any incline in high and low range and sometimes stalls when I let off of the throttle or change gears. When I apply throttle in neutral, it sounds like it is struggling for fuel/air and pops. When I decelerate, there is a grinding sound coming from the clutch, which I've read to be related to the one way bearing and is semi-common. The last thing I've observed is sometimes the speedometer display sometimes will show a much higher value for a few seconds after barely touching the throttle. Based on the documentation, if a problem is detected from the sensors, the instrument panel display should have an error code rendered on the screen in place of the time, but this isn't happening. Here is a video showing some of these issues (engine is exposed with console removed):
      https://www.youtube.com/watch?v=FFAkO5TaGps
       
      Here is another video of the clutches in action:
       
      I've done some research, but information on this specific unit and sister units is limited. There does seem to be transmission and clutch issues reported. I still need to check into the head gaskets. I don't have the equipment to test compression right now, but I do plan on ordering what is needed soon. I do have an order in place for some cables to read the diagnostics from the computer. There is a shop two hours away from me that works on Hisun products, but I am hoping the problem can be identified and is something within my ability to handle. Below is what I've already investigated.  I am leaning towards the primary clutch needing replacement right now.
      After getting it home and unloaded, I did the following maintenance/checks to it prior to operating it further:
      Changed the engine/clutch oil (and filter) and gear oils using manufacture recommended viscosity Changed the air filter and checked for cracks in the air intake flow. Verified good suction. Cleaned the throttle body Changed the spark plug and verified the gap was within spec (0.6-0.7mm) Changed the coil and coil wire Changed the fuel lines, fuel injector, and verified the fuel pump was outputting the correct initial prime pressure for ignition and continuous pressure after ignition. Also completely emptied the fuel tank and made sure octane 91+ fuel is being used per manufacturer specs. Ran seafoam through system too. Cleaned the spark arrester and verified no cracks or gaps in the exhaust flow Changed out the O2 sensor Checked all wired connections to ensure they were secured and no breaks were visible Checked the belt for tightness and for any signs of wear and tear Verified 4WD and the differential lock function as expected - still hesitates and struggles uphill Verified the fan gears in the shifter are not corroded and working as expected ECU was reset after replacing sensors and fuel-related parts  
       
      Thanks!
    • Hugh
      2018 Hisun Sector Crew 1000 engine die after about 15 minutes run
      By Hugh
      My 2018 Hisun sector crew engine cut off after about 15 minutes run. There is no indicator of what is wrong, no error code just die and won't restart until it cool down. I notice that the fan is not running but the temp indicator is on low temp, no overheat indicator. I checked the radiator fluid, it is cool to touch.
      Cooling fans are working, I can hear it running once awhile if I can get the engine warm up enough.  Thank you for all the help.
       
      Hugh
    • Hi sun 500
      2011/14 Hisun 500 fuel issue
      By Hi sun 500
      hello everyone, i just joined this forum to try my luck, few days ago i bought an old (dont know exactly), 2011/14 hi sun 500cc ""carburated"",  was not running at the time, but i fell was a good deal and decided it to bring it home to play with it, this is the issue, i bought and installed a new carb, and pump, i repositioned the battery location and upgraded to a "car batt", reconnected the fuel lines and started it, but it only runs with the choke ON, i checked the bowl, it does have fuel,but for some reason wont inject it to run, i came across a video that say that ""the body small tank had to be connected for the cart to run" (was deleted when bought), sure enough i got it to run sporadically , but the so called ""small body tank'' often runs out of fuel and wont refill itself , i had to couple times do it manually, so how does that small tank works ?..what does it do?..and why if  bypass it , the cart wont start?....any help?..thanks so much!!!
    • aefron88
      Hisun HS400/Coleman UT400 Parts Diagrams
      By aefron88
      View File Hisun HS400/Coleman UT400 Parts Diagrams
      Compiled document with parts diagrams for Hisun HS400/Coleman UT400 for help in repairs where the service manual diagrams are poor or non existent.
      Submitter aefron88 Submitted 04/15/2024 Category Hisun  
    • Nypto
      Hisun 750 Total electrical failure
      By Nypto
      I just bought a new Hisun 750 sxs. I drove one mile and it just died. No power at all. Battery is 12.8v. Found no blown fuses. No power to the panel, no nothing. Problem for me is I bought 160 acres near big bend. Trying to build a house. Got blown up in 'Nam . Can't walk much. Scared I'm way out and it fails again. I heard something  about a brake switch,  but I have no idea where it might be.

UTV FORUMS

MORE SECTIONS

FOLLOW US ON

GET IN TOUCH

  • Automotive Webmaster
×
×
  • Create New...