Quantcast
Jump to content


Recommended Posts

Posted

I’ve searched all over and haven’t been able figure out the maker and model of my buggy. It appears to be some kind of Joyner maybe an older model?  Anyone know what this is?  it appears to be 1000cc and it’s a 4  cylinder thx 

C8E4DBAD-30A0-44F7-9FB5-8425E4D7C662.jpeg

EE15A8E4-586D-401F-8DA2-E6003F5FE859.jpeg

AA36100A-9724-47F6-9624-B2C7950DA216.jpeg

53B5E75D-AF17-4B2F-85AA-BB33F0970E04.jpeg

983E9E80-BD7E-4D83-B049-8661306CDF19.jpeg

  • Like 1
Posted

Have  you looked for any numbers on the engine? It looks very similar to the sandviper, but the 2 front metal bars are different than the viper.

overall it's a good looking machine, and Welcome to the board!

  • Like 1
Posted

There's got to be a manufacturer plate on it somewhere. It'll have the vehicles info on it. I'd get it up in the air where I could inspect the bottom thoroughly. I'm assuming you've inspected all that's visible on the top side. 

  • Like 1
Posted
6 hours ago, kenfain said:

There's got to be a manufacturer plate on it somewhere. It'll have the vehicles info on it. I'd get it up in the air where I could inspect the bottom thoroughly. I'm assuming you've inspected all that's visible on the top side. 

Yep, I looked all over and no identifying marks anywhere. I’ll have to get underneath it. I have however discovered it’s not a 4 cylinder, it’s actaully a 3 which means  it’s a suzuki F8B (800cc) or at least a clone....

Posted

Looks like it would be a lot of fun to drive. But with those open wheels, I think you'll be wearing whatever you're driving through. You should also look for a stamped number on the frame. I'd think that it would be in the cockpit. Those numbers are hard to spot, since they're painted over. Good luck, and welcome to the forum.

  • Like 1
Posted
9 hours ago, kenfain said:

Looks like it would be a lot of fun to drive. But with those open wheels, I think you'll be wearing whatever you're driving through. You should also look for a stamped number on the frame. I'd think that it would be in the cockpit. Those numbers are hard to spot, since they're painted over. Good luck, and welcome to the forum.

I think most manufacturer's put the stamp below  or around the seats.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Popular Now

  • Similar Topics

    • By rdc
      Hope I posted this in the right place. Looking for the left side shaft carrier where the rear bearings go for an 1100cc sand viper, I understand an 800 cc carrier will also work. I need the old style two bearing with the spacer in the middle, the new style with just the one wide bearing wont work. If anybody has one I'll buy it right away. my email is [email protected]
    • By 180gtr
      Parting out a rolled Sand viper 1100. I will list some of the parts I have, otherwise ask me if there is something specific you are looking for. I am selling everything I have for $800. I am located near Glenwood Springs CO.
      SOLD ITEMS, I do not have these items.
      Wheels
      Tires
      Engine
      Transmission
      Axles
      Shocks
      Control Arms
      Things I have....These all came off of the running engine. I have video of it running if anyone needs to verify that.
      Throttle Body $90
      Starter $150
      Alternator $150
      Fuel rail, injectors, fpr $100
      fuel pump $70
      Map Sensor $50
      Full set of Guages $150
      Exhaust w cat, O2 SOLD
      Ignition Coil - SOLD
      Wiring harness and ecu SOLD
      Radiator, shroud, elec fan, overflow tank $200
      Fuel tank w sender $150 Has dent at base of fuel neck, no leaks
      I have a box full of misc bolts, nuts, etc.
      I will sell the Chassis or Frame alone for $200. The chassis is in pretty good shape, needs some cage repair and 2 areas straightened where control arms mount. If anyone had an automotive frame machine it would take a few hours.
      That would include....
      Brake calipers, lines, pedal, master cyl, E brake assy,
      Steering shaft, wheel
      Ignition switch, key
      Light bar frame, 2 lights
      misc hardware, spindles
      2 hubs, rotors
      Engine mounts
      Throttle pedal, cables
      Shifter, cables
      Clutch master, pedal
      I am sure I am forgetting something.
      I am parting this out of ebay right now, I just picked up another project and could use the room. No I will not take less than $700 for all of it or $200 for the frame. I do not need to sell it, I will make far more parting it out but would like the extra space in the garage.
      If interested I also have an 07 1000rr engine setup I would sell with the buggy for $650.
      Thanks!
















    • By Jody Deville
      I’m looking to best place to buy replacement axles for the rear in my buggy. Both axles are bad. Where is the best place to find them?
    • By Timbo
      I never see videos of hear of people taking these things to the big trails. Do you ? I just got one and want to.
       
×
×
  • Create New...