Quantcast
Jump to content


Recommended Posts

Posted

Hi All,

New here, but bought a 2022 Sector 750 brand new last march (old stock up here in Canada)

It's a good bike so far, but I have noticed a quirk and was wondering if anyone else has had a similar issue?

 

The issue I've had is if I leave the utv parked on any incline, not even a major incline, and leave it to sit for a while (day or two) it will not start properly. It will turn over and not fire until I press the gas pedal, when it will run and rev up, but if I let off the gas it will die. It will keep doing this until I either start it in gear and drive it for a bit or leave it in neutral and roll it down the hill to flatter ground. where it will have to sit for a while. 

If I park it on a decline there is no issue. fuel is not low, it's occurred a couple times now. 

 

Any thoughts on the cause of this? Dealership just says bring it in and let them take a look, at my expense of course. 

  • 2 weeks later...
Posted

I would check for fuel contamination, water or too much ethanol in bottom of tank. I have a Hisun tech coming Monday to check my 2022 sector for that condition, mine loses power going up my long-inclined driveway.

nods

  • 2 months later...
Posted

Well, it was interesting to watch the road tech replace EVERYTHING;  the fuel pump and sender assembly, new fuel lines, fuel filter, Injector, HEGO, TPS, and IAC. One thing he was talking about the most is water/ethanol contamination, which would settle out to the bottom of the fuel tank when parked for a day or more. Once driven it would mix in the tank and the severity of the problem would go away. He looked in my tank and really didn't see this in mine, although there seemed to be like water marks in the very bottom of the tank. He wiped it out and then filled it with premium fuel that has no ethanol. My running concern has gone away, and the unit runs really very nice now. Of course, having that many parts replaced is like a shotgun blast, hard to miss. I did end up with another electrical problem just before this last repair. it was supposed to have been fixed and was not! It is intermittent short in the main loom, (the engine loom was already replaced for another issue.) When driven on the road about 1 mile the fuse for the signal lights blows. Have no brake lights or turn signals and causes feedback in the instrument display. Hisun picked it up yesterday to take it back to Texas to replace the main loom that was supposed to have been replaced 3 months ago.

So, I guess the bottom line is check for fuel contamination. Do not use fuel that has ethanol added! The fuel pump retaining ring on the tank is really tight, watched the tech bust a sweat trying to get it off then back on, he was a very BIG dude and was using a very special tool.

You might try to get a gas sample after letting it for a couple of days in the position that gives you the worst starting problem, check for obvious contamination and then google how to check for ethanol in gas. If you find any fuel issues, make sure you replace the fuel filter. 

Hope my ramblings help you.

NOD

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Similar Topics

    • By Rschrem
      Hi, my 2010 Hisun will crannk but comes to a stop and only clicks.  It has new battery and solinoid. Battery connections all seem good. Any ideas what the problem is? 
    • By Xov
      Just received delivery of a 2024 AMP Pro.  Thought I'd start a thread with my impressions as I use it and learn more.  There doesn't seem to be a whole lot of real-world usage information out there on this model.  Hope this will help others as they research.
      Intended Use Cases
      Fire mitigation / slash removal from a 5 acre forested and well-gamble-oaked property.  The previous owners thought as much about fire mitigation as I do about fashion: not much. Snow removal Stump pulling General hauling (rock, lumber, etc.) Weimaraner energy depletion.  Wasn't an original use case, but a nice added bonus.  Experiences So Far
      Wasn't impressed that two of the bumpers on the underside of the bed where it sits upon the frame were missing.  The metal on metal contact has damaged the powder coating and the frame.  I expect a little better QC.
      I've only put a few hours on it, so not a ton to report on usage.  It isn't quiet; it's silent.  I can't even detect an electric note from the motor. I removed (and subsequently replaced) the motor cover noticed that the motor is German and made by Schambuller.  The motor controller is Italian and made by Dana TM4.  Given the operating specs of both I found on the web, I suspect both are higher quality than the previous Navitas (which is supposed to be decent).  The motor is rated at 25 hp and 71.5 lb-ft of torque.  It feels very powerful.  All the torque is delivered instantly, if desired.
      The bed is huge and has an electric dump as standard.  Great feature but would like it to go up a bit more.  Probably not feasible from an engineering perspective, but I want and I need ;).
      Power steering is nice, but vague.  Probably common to many UTVs, but I am accustomed to more direct results from input.  Plan early and plan often.
      In our first full day of usage, we hauled about 1/2 as much slash as the entire rest of the year when I was doing it by hand cart.  I may get fatter, but I'll also get more done.  After a few days of usage, the battery meter has gone down by 1/10th. 
      Until next time...


    • By Tim n Deb
      Riding out today it acted like it ran out of gas,  stalled and died and would not start.   Towed back to house,  New  plug added this past month,  plenty of oil, getting plenty of gas, battery cranks good.   Trys to kick in and starts but doesnt.   Two days prior while sitting at a idle it died.  Added gas and it started did my ranch chores with it.  But just now it stalled out cranks but will not start.   Tried to find if fault codes came up on the clock like manual says but not sure I am doing that right.  Any and all help apprecated.  Thank you
    • By monkthumper
      Fuel pump is good (i hotwired it) swapped relay with known good one no help. I'm leanin towards ECU but cannot find wiring diagram online. Dont know how fuel pump relay gets its signal, all fuses good, any help? 
    • By Pick a name
      The Axis 500 will not shift into low or reverse.  I have high when it should be in low and all the other places it is reverse.  The gears in the shift cover are fine and I shifted it when the cover was off and yet no change (so it can't be the shifting mechanism gears).  I t has been difficult to get it into low for awhile.  But now it is either high or reverse, no neutral either.
×
×
  • Create New...